Jet Propulsion and Compressor Design NASAs X43 A

Jet Propulsion and Compressor Design NASA's X-43 A Keith Larson IC Engines and Propulsions Systems Spring 2005 Professor Dr. Chiang Shih

Fluid Machinery Positive Displacement • Working fluid is confined within a boundary. • Energy transfer is by volume changes due to the movement of the boundary. Dynamic • Working fluid is not confine within a boundary. • Energy transfer is by dynamic effects of the rotor on the fluid stream.

Dynamic Machine A. K. A. Turbomachines * Radial-Flow - Also called Centrifugal. - Radial flow path. - Large change in radius from inlet to outlet. * Axial-Flow - Flow path nearly parallel to the axis of rotation. - Radius of the flow path does not very significantly. * Mixed-Flow - Flow path radius changes only moderately.

Turbomachines that extract energy from the fluid stream Turbines use Vanes, Blades, or Buckets attached to the turbine shaft. This assembly is called the Rotor, Wheel, or Runner. Bourn, Cambridgeshire, England Colvin Run Mill near Dranesville, Virginia

Turbine Classifications * Hydraulic Turbines - The working fluid is WATER. - Flow is incompressible. * Gas and Steam Turbines - Density of the working fluid may change significantly. Further Classification • Impulse Turbines - Driven by one or more high-speed free jets. - Each jet is accelerated in an external nozzle. - Fluid acceleration and pressure drop is external to the blades. • Reaction Turbines - Part of the pressure change takes place externally and part takes place within the moving blades.

The turbine extracts energy from the fluid stream and converts it into mechanical energy, which is then transmitted through a shaft to some load. The Steam Turbine Generator Satsop Development Park

Or the load could be a compressor within a Turbocharger for an automobile, or a compressor in a jet engine.

Turbomachines that add energy to the fluid stream * Pump - when the fluid is a liquid or a slurry. · Very small to very large pressure rise. · Rotating element is called an impeller. * Fans, Blowers, or Compressors when handling a gas or a vapor. • Fans - generally have a small pressure rise (< 1 inch water) • Blowers - moderate pressure rise (1 inch of mercury) • Compressors - very high pressure rise (up to 150, 000 psi)

Jet Propulsion Principle (Thrust) Pa T T Po Pa T: Thrust Po Pa: Ambient Pressure ue Steady-Flow T T=Ai(po-pa) Po Pa Pa Ai Po: Internal Pressure ue: Exit Velocity . T=mua Po ua ua: Mass-average Exhaust Velocity

Thrust per Unit Energy Consumption (Rocket vs. Propeller) Engine u ue Acceleration of a stream of air through a Propeller Thrust Ratio . T=ma(ue-u) . T E . . Assume a best thermal efficiency of 40%, the maximum possible value of propeller thrust ratio becomes. . T E

Rocket T m • puer • E • T • E Rocket Thrust Ratio Estimate ratio of propeller and rocket thrusts T T Assume that the rocket exhaust velocity is 5000 m/s. T T

Summary of Propeller and Rocket Thrust Þ For Aircraft propulsion the big advantage of using a propeller is that less fuel must be carried on board. • The rate of airflow through the propeller can be as much as three orders of magnitude larger than the rate of fuel consumption of the driving engine. ÞPropulsion using a propeller has much better efficiency when compared to propulsion with a rocket. • The aircraft using a propeller can travel much greater distances before having to refuel.

Propeller Theory Air Velocity (u) Axis of Rotation Air Motion Blade Speed (Ut) w 1 t Relative Approach u Velocity (w 1 t) Ut Relative Leaving Velocity (w 2 t) Blade Motion Swirling Velocity (u ) u D w 2 t w 1 t c 2 Ut u ue Axial Component of Leaving Velocity (ue) Leaving Velocity (c 2) Turning Angle ( )

Limitation of the Propeller in Propulsion In order to maintain good flow over the blade certain conditions must be meet. 1. The relative approach angle and the blade leading edge angle must be close to prevent flow separation from the blade. 2. The turning angle must be keep quite small, or the flow will also separate from the blade. 3. The relative approach velocity must not be too close to the speed of sound. This is to prevent shock waves from forming on the blade. Thus conventional propellers are used for flight speeds well below the speed of sound; usually at or below 135 m/s (300 mph).

Axis Air Motion w 1 t Ut Blade Motion Blade speed too high u Flight speed too slow Operating outside of design parameters Axis Poor design: Turning angle is too large Air Motion w 1 t u Ut Blade Motion

The Importance of the Compressor/Turbine in Modern Flight It was not until 1939 that a compressor, combuster, and turbine were coupled together to create the first turbo engine for aircraft propulsion. Air Inlet Exhaust Gas Out

1. The turbine engine made supersonic flight possible in aircraft 2. Reduced the cost of air travel. 3. Lead to great improvements in aircraft safety.

Turboprop Allison T 56 Turboshaft

Turbofan General Electric CF 6 Turbofan

Turbojet General Electric J 79 Turbojet with Afterburner

Turbo Engine Comparison Turboprop Turbofan Turbojet • Medium-speed • Internal Propeller • High speed • Moderate-size craft • Supersonic speeds • Mach 4 • High efficiency • High bypass airflow • Low airflow rate • Limited flight speed • Med/High efficiency • Low efficiency • Geared transmission • No gearbox • High op temps NOTE: Due to the ram compression due to flight speed, the optimum compressor pressure ratio (CPR) goes to zero around Mach 4. CPR 30: 1 for subsonic flight. CPR 10: 1 @ Mach 2. Compressor not needed at Mach 4; Ramjet.

Comparison of the Axial-Flow and Radial-Flow Compressors Axial-Flow compressors do not significantly change the direction of the flow stream, thus Axial-Flow Compressor allows for multiple stages. Radial-Flow Compressors can not be staged. While the Radial-Flow Compressor has a larger Compressor Pressure Ratio (CPR) per stage, the multi-stages of the Axial-Flow compressor allows for a larger overall CPR. The frontal area for a given air flow rate is smaller for an Axial-Flow Compressor than for a Radial-Flow Compressor. The Axial-Flow Compressor has a higher efficiency. Disadvantages are the higher cost to manufacture the Axial-Flow Compressor, and the Radial-flow Compressor is more durable than the Axial-Flow Compressor.

Example Problem Given a first single stage of an Axial Compressor with the following conditions: ambient pressure (Pin) 1 atmosphere, ambient temperature (Tin) 300 K, aircraft cruising speed (Vin) 170 m/s, median blade diameter (D) 0. 5 m, rotor rpm (Urotor) 8000 rpm, turning angle ( ) 15 degrees, specific heat ratio ( ) 1. 4, air mass flow rate (mdot) 35 kg/s, and (Cp) conversion factor 1004 m 2/s 2*K, calculate the first stage Compressor Pressure Ratio (CPR).

Step 1. Vin W 1 U Blade motion Create the velocity triangle and calculate the relative speed of the rotor blade from the rotational velocity.

Vin W 1 U Step 2. Calculate the air to blade relative velocity and the angle between the relative and actual air speed.

Step 3. W 2 Vin Axial velocity (Vin) does not change. Calculate relative exit angle( 2), then portion of the relative blade speed (Uw 2). Calculate relative air speed (W 2)

Step 4. V 2 W 2 Vin Calculate the portion of the relative blade speed associated with the actual air velocity (Uv 2), the calculate the actual air speed (V 2).

The Compressor Pressure Ratio (CPR) is found from the isentropic relationship. To 1 is calculated from the following equation. To 2 has to be calculated from the specific work of the compressor stage.

Specific work of the stage is calculated from the torque of the shaft, angular velocity of the blade, and mass flow rate of the air. Torque of the shaft is: No initial tangential component to the inlet velocity. Power of the shaft is:

Specific work of the stage is then: Now To 2 can be calculated from the specific work To 1, and the conversion factor.

Finally, the Compressor Pressure Ratio can be calculated!!! The answer is:

The engines on the blackbird are turbojets and are used as such up to about Mach 4; when the air flow is bypassed around the compressor and the engines become ramjets. Lockhead SR-71 Blackbird

NASA X-43 A This is where we are today. The X-43 A is an experimental aircraft that uses a scramjet (supersonic ramjet) for its propulsion. The X-43 A has reach speeds of about Mach 10.