Teknologi Las Kapal Aplication TIG Welding for Non

Teknologi Las Kapal Aplication TIG Welding for Non Ferro Proper Techniques and Procedures

Objectives v Duplicate the procedure for preparing tungsten rods for tig welding in writing with no errors v Describe how to insert the tungsten rod into the wand with a partner with no mistakes v Identify all parts of a tig welder on a quiz with 90% accuracy v Demonstrate the arcing process and filler rod control with 30% accuracy v Demonstrate in a one on one basis with the teacher the welding process of maintaining proper arch length and filler rod feed with 30% accuracy Teknologi dan Rekayasa

Introduction Cont. v TIG welding is considered highly artistic. The fine detail and quality of the welds produced depend on the artist. v However TIG welding is used to weld mild steel, aluminum, and stainless steel. Teknologi dan Rekayasa

TIG Welding v In TIG welding an arc is formed between a nonconsumable tungsten electrode and the metal being welded. Gas is fed through the torch to shield the electrode and molten weld pool. If filler wire is used, it is added to the weld pool separately. Teknologi dan Rekayasa

TIG Machines Foot Control Ground torch Regulator Argon 100% Teknologi dan Rekayasa

Torch Back Cap Tungsten Rod Ceramic Tip Teknologi dan Rekayasa

Foot Control v Practice controlling the heat with the foot pedal to see the weld puddle increase and decrease. Ideally, you want your weld puddle to be about 1/4 inch wide. Keep your puddle size consistent so it doesn't grow, shrink, spread or narrow while you are welding. Teknologi dan Rekayasa

Tungsten Types v 2% Thoriated Tungsten - AWS Class EWTh-2 RED Generally used for DC negative or straight polarity applications, this is the most common type of electrode used today. Provides excellent resistance from weld pool contamination, easier arc starting capabilities and a more stable arc. Contains 2% weight of thorium oxide (Th. O 2). Most common metals used for include: Carbon and Stainless Steel, Nickel Alloys, and Titanium. v Pure Tungsten - AWS Class EWP GREEN Used for AC welding applications. Ball the end to provide good arc stability. Typically the least expensive tungsten, but is more susceptible to weld contamination than thoriated, ceriated or lanthanated. Contains a minimum of 99. 5% weight tungsten with no other alloys. Most common metals used for include: Aluminum and Magnesium Alloys (AC). Teknologi dan Rekayasa

Tungsten Types v 2% Ceriated Tungsten - AWS Class EWCe-2 Orange Used for AC or DC welding applications. An excellent alternative to Thoriated tungsten especially in low amperage welding. Takes approximately 10% less current to initiate arc and has a very stable arc. Not a radioactive material and tends to last longer than thoriated. Contains 2% weight of Cerium Oxide (Ce. O 2). Most common metals used for include: Carbon and Stainless Steels, Nickel Alloys and Titanium. Teknologi dan Rekayasa

Tungsten Types v 1% Zirconiated Tungsten - AWS Class EWZr-1 Brown Used for AC welding applications. Better start up than pure tungsten, balls up well and has a more stable arc. Better current carrying capacity and high resistance to contamination during welding. v 2% Lanthanated Tungsten - AWS Class EWLa-2 Blue Also called "rare earth" tungsten. Used for AC or DC welding applications. Characteristics are similar to ceriated, and is also non-radioactive. Contains 2% Lanthanum Oxide (La. O 3). Most common metals used for include: Carbon and Stainless Steels, Nickel Alloys and Titanium. Teknologi dan Rekayasa

Most Common Tungsten Rods Teknologi dan Rekayasa

Tungsten Rod Preparation Teknologi dan Rekayasa

Tungsten Rod Preparation Teknologi dan Rekayasa

Torch and Filler Positioning Teknologi dan Rekayasa

Welding Operation Teknologi dan Rekayasa

Proper Clothing v v v Long sleeve Shirt no frayed edges Cotton pants with no frayed edges Welding Gloves Close toe shoes Welding Helmet Not Automatic Shield Preferably 10 or higher due to bright arch Teknologi dan Rekayasa

Lets Get Started v Get dressed v Get a welding helmet and meet me at the set up station v I will demonstrate proper arc length, torch angle, and filler rod feeding v After shop-work, a quiz will be given over the parts of the welder Teknologi dan Rekayasa

WELD-SEAM PREPARATION Teknologi dan Rekayasa

WELD-SEAM PREPARATION Teknologi dan Rekayasa

WELD-SEAM PREPARATION Teknologi dan Rekayasa

WELD-SEAM PREPARATION Teknologi dan Rekayasa

WELD-SEAM PREPARATION Teknologi dan Rekayasa

SHOW TIG welding Teknologi dan Rekayasa

Knowledge is the key to success Teknologi dan Rekayasa