Training Manual 1 st Edition ANSYS Workbench Simulation
Training Manual 1 st Edition ANSYS Workbench Simulation Introduction
Training Manual ANSYS Workbench – Simulation Introduction Inventory Number: 002265 1 st Edition ANSYS Release: 10. 0 Published Date: August 26, 2005 Registered Trademarks: ANSYS® is a registered trademark of SAS IP Inc. All other product names mentioned in this manual are trademarks or registered trademarks of their respective manufacturers. Disclaimer Notice: This document has been reviewed and approved in accordance with the ANSYS, Inc. Documentation Review and Approval Procedures. “This ANSYS Inc. software product (the Program) and program documentation (Documentation) are furnished by ANSYS, Inc. under an ANSYS Software License Agreement that contains provisions concerning non-disclosure, copying, length and nature of use, warranties, disclaimers and remedies, and other provisions. The Program and Documentation may be used or copied only in accordance with the terms of that License Agreement. ” Copyright © 2005 SAS IP, Inc. Proprietary data. Unauthorized use, distribution, or duplication is prohibited. All Rights Reserved. August 26, 2005 Inventory #002265 TOC-2
ANSYS Workbench – Simulation Introduction Table of Contents Introduction A. B. C. D. 2. Simulation Basics A. B. C. D. 3. B. C. D. E. F. Geometry Branch 3 -5 Contact 3 -14 Meshing 3 -32 Named Selections 3 -58 Coordinate Systems Workshop 3 – Mesh Control 1 -10 1 -24 2 -3 G. H. I. J. K. 2 -42 C. D. E. F. G. 7. C. 8. Geometry 4 -4 Assemblies – Solid Body Contact 4 -9 Loads and Supports 4 -18 Workshop 4. 1 – Linear Structural Analysis 4 -38 Solution Options 4 -39 Results and Postprocessing 4 -43 Workshop 4. 2 – 2 D vs 3 D Analysis 4 -56 A. B. C. D. Free Vibration Analysis Procedure Workshop 5. 1 – Free Vibration with Pre-Stress Workshop 5. 2 – Prestressed Modal 5 -4 5 -16 5 -17 5 -23 9. Background on Buckling Analysis Procedure Workshop 7 – Linear Buckling 6 6 7 -1 7 -3 7 -8 7 -21 Results Postprocessing 8 -1 A. Viewing Results 8 -3 B. C. D. E. F. G. H. I. Free Vibration Analysis 5 -1 6 -1 Geometry 6 -6 Assemblies – Solid Body Contact 6 -9 Heat Loads 6 -19 Solution Options 6 -27 Results and Postprocessing 6 -31 Workshop 6. 1 – Steady State Thermal Analysis -36 Thermal Transient Setup 6 -38 Transient Settings 6 -41 Transient Loads 6 -46 Transient Results 6 -48 Workshop 6. 2 – Transient Thermal Analysis -51 Linear Buckling Analysis A. B. 3 -63 3 -66 4 -1 Thermal Analysis A. B. C. D. E. F. 2 -1 Launching Simulation Startup Panel 2 -13 Basic Procedure 2 -17 Workshop 2 – Simulation Basics Static Structural Analysis A. B. 5. 6. General Preprocessing 3 -1 A. 4. 1 -1 About ANSYS, Inc. 1 -5 ANSYS Workbench Overview Starting Simulation 1 -20 Workbench Projects Scoping Results 8 -21 Exporting Results 8 -26 Coordinates Systems 8 -29 Solutions Combinations 8 -31 Stress Singularities 8 -34 Error Estimation 8 -37 Convergence 8 -39 Workshop 8 – Advanced Results Processing -49 8 ANSYS Workbench – Simulation 1. Training Manual CAD & Parameters 9 -1 A. CAD Interoperability B. C. D. E. 9 -3 Multiple Design Studies 9 -31 Design. Xplorer 9 -39 Parameter Manager 9 -40 Workshop 9 – Design. Xplorer Parameter Mgr. -47 9 August 26, 2005 Inventory #002265 TOC-3
ANSYS Workbench – Simulation Introduction Table of Contents Harmonic Analysis A. B. C. D. E. 10 -1 Harmonic Analysis Procedure Solving Harmonic Analyses Damping Input 10 -22 Request Harmonic Tool Results Workshop 10 – Harmonic Analysis 10 -7 10 -15 10 -28 10 -37 ANSYS Workbench – Simulation 10. Training Manual August 26, 2005 Inventory #002265 TOC-4
- Slides: 4