The ultimate chain lubrication system LC Low Cost

The ultimate chain lubrication system. LC – Low Cost Lubrication Kits Extend Chain Life not the Chain – Improve Cleanliness –Reduce Amps – Reduce Oil consumption

Kit Part Number RSL-LC-200 -08 B 1 RSL-LC-200 -10 B 1 RSL-LC-200 -12 B 1 RSL-LC-200 -16 B 1 RSL-LC-200 -20 B 1 RSL-LC-200 -24 B 1 RSL-LC-1000 -08 B 1 RSL-LC-1000 -10 B 1 RSL-LC-1000 -12 B 1 RSL-LC-1000 -16 B 1 RSL-LC-1000 -20 B 1 RSL-LC-1000 -24 B 1 Kit Description. Oil Pump (0. 2 Ltr) with ½” BS Applicator Oil Pump (0. 2 Ltr) with 5/8” BS Applicator Oil Pump (0. 2 Ltr) with 3/4” BS Applicator Oil Pump (0. 2 Ltr) with 1 ¼” BS Applicator Oil Pump (0. 2 Ltr) with 1 ½” BS Applicator Oil Pump (1. 0 Ltr) with ½” BS Applicator Oil Pump (1. 0 Ltr) with 5/8” BS Applicator Oil Pump (1. 0 Ltr) with 3/4” BS Applicator Oil Pump (1. 0 Ltr) with 1 ¼” BS Applicator Oil Pump (1. 0 Ltr) with 1 ½” BS Applicator LC- Low Cost Rotalube Lubrication systems supplied in a kit.

Quantity 1 Part Number Description RSL-LC-1000 Or RSL-LC-200 Pneumatic Lubrication Pump complete with 0. 2 litre or 1 Litre Reservoir has oil sight gauge attached and pump air/oil outfeed is supplied with 2 m of 6 mm OD feed Pipe 1 RSL-LC-B 1 Or RSL-LC-B 2 Mounting Bracket for the pump 1 See attached. For options Rotalube applicator with one 6 mm OD push fit inlet fitting. LC- Low Cost Rotalube Lubrication systems supplied in a kit.

Chain Size Part No 3/8” A (mm) B (mm) C (mm) D (mm) E (mm) Inlet (mm) RSL-LC-06 B 1 38 19 Ø 10 16 Ø 40 Ø 6 O. D 1/2” RSL-LC-08 B 1 41 19 Ø 10 16 Ø 44 Ø 6 O. D 5/8” RSL-LC-10 B 1 40 19 Ø 10 16 Ø 46 Ø 6 O. D 3/4” RSL-LC-12 B 1 44 21 Ø 10 16 Ø 48 Ø 6 O. D 1” RSL-LC-16 B 1 53 25 Ø 10 16 Ø 56 Ø 6 O. D 1 1/4” RSL-LC-20 B 1 58 28 Ø 10 16 Ø 6 O. D 1 1/2” RSL-LC-24 B 1 68 33 Ø 10 16 Ø 76 Ø 6 O. D LC- Low Cost Rotalube Lubrication systems supplied in a kit.

1. Mount the LC Lubrication pump onto the bracket provided. 2. Connect the air supply, air supply to be manually controlled by an on/off isolation valve or electrically by solenoid valve. The Solenoid valve could be controlled by a controller or machines PLC. Solenoid or manual ball valve are not included in the kit. Ensure the air is off at this point. 3. Mount the Rotalube onto the chain , detailed in the Installation section The applicator must be no further than 2 M from the lubrication pump. 4. Simply connect the feed line that is attached to the pump to the Rotalube inlet. The inlet is 6 mm OD push in. 5. Fill the Reservoir with recommended oil as detailed in on Page 7. 6. Once the pump has oil in the reservoir and the filler nipple sealed allow regulated air supply to the pump. The air pressure must be less than 20 PSI. The system will take approximately 1 -2 minutes to prime and then the feed pattern can be seen at the Rotalube applicator. Should the air oil feed from the applicator be too much –reduce the air pressure into the pump. Each application will have its own optimum air pressure requirement and this will be anywhere between 5 and 20 PSI LC- Low Cost Rotalube Lubrication systems supplied in a kit.

Mounting holes. Directions for correct mounting of Timken ILS Ltd Rota. Lube Applicators – It is vital that the Rota. Lube Applicator is installed by following these instructions. Failure to adhere to the following will result in the Rota. Lube Applicator not functioning correctly. Indicator to show Direction of the lubricant feed. Each Rota. Lube applicator has an exterior indication of the position for correct installation identified by a drilled spot located directly below the two mounting holes (as shown). The Rota. Lube Applicator MUST be positioned on the chain with the mounting holes in a horizontal plane and the location pin pointing directly down onto the chain link/pin. Never rest the Rota. Lube directly onto chain roller, Always have the applicator mounted off the roller LC- Low Cost Rotalube Lubrication systems supplied in a kit.

To Fill the LC Lubrication Pump – • Isolate the air from the pump • Remove the Filler Plug at the top of the pump head as shown • Fill with the recommended Lubricant • Lubricant supplied in 500 cc bottles fitted with twist lock directional spouts. LC- Low Cost Rotalube Lubrication systems supplied in a kit.

Quality, lubricants suitable for penetrating Chain with good lubricating properties. Operates well in the LC lubrication systems Resulting in reduced chain wear and friction, reducing power consumption and increases service life. Lubricants RSL 1 -ISO UV 32 -500 Kluber. Oil 4 UH 1 -N-500 Chain Oil for Rotalube LC Pumps & Applicators High Performance Chain Oil Food Grade Oil H 1 approved Pack x 6 Extend Chain Life not the Chain – Improve Cleanliness –Reduce Amps – Reduce Oil consumption

Extend Chain Life not the Chain – Improve Cleanliness –Reduce Amps – Reduce Oil consumption