Technician License Class Technician Class Chapter 5 Amateur

  • Slides: 168
Download presentation
Technician License Class

Technician License Class

Technician Class Chapter 5 Amateur Radio Equipment

Technician Class Chapter 5 Amateur Radio Equipment

Modulation Bandwidth. • A simple sine wave signal occupies only a single frequency in

Modulation Bandwidth. • A simple sine wave signal occupies only a single frequency in the spectrum. • A signal consisting of multiple sine waves is called a composite signal. • The individual signals that make up the composite signal are called components of the signal. • The size of the range of frequencies occupied by a composite signal is called its bandwidth.

Modulation Bandwidth. • The human voice is a composite signal containing many different frequencies

Modulation Bandwidth. • The human voice is a composite signal containing many different frequencies simultaneously. • The lowest frequency component of the human voice is approximately 300 Hz. • The highest frequency component of the human voice is approximately 3000 Hz. • Therefore the bandwidth of the human voice is about 2700 Hz (3000 Hz – 300 Hz).

Modulation. • A simple radio signal with a constant amplitude and a constant frequency

Modulation. • A simple radio signal with a constant amplitude and a constant frequency conveys no information and cannot be used to communicate. • In order to communicate, we must add some information to the simple radio signal. • Adding information to a signal is called modulation. • Retrieving the information from the signal is called demodulation or detection.

Modulation. • A simple RF radio signal is called a carrier or a carrier

Modulation. • A simple RF radio signal is called a carrier or a carrier wave because it “carries” the information. • Modulation converts a carrier into a composite signal, increasing its bandwidth. • Bandwidth depends on modulating method and the characteristics of the modulating signal.

Modulation. • A carrier can be modulated by changing any of its characteristics: •

Modulation. • A carrier can be modulated by changing any of its characteristics: • Amplitude = Amplitude Modulation (AM). • Frequency = Frequency Modulation (FM). • Phase = Phase Modulation (PM). • Different types of modulation are called modes. • CW, AM, SSB, FM, PM, etc.

Modulation Continuous Wave (CW). • The simplest method of modulation is to merely turn

Modulation Continuous Wave (CW). • The simplest method of modulation is to merely turn the signal on and off in a particular pattern, such as Morse code. • This mode is known as continuous wave or CW.

Modulation Amplitude Modulation (AM). • In AM, the strength of the carrier is changed

Modulation Amplitude Modulation (AM). • In AM, the strength of the carrier is changed to match the changes in the strength of the modulating signal.

Modulation Amplitude Modulation (AM). • AM signals consist of three components: • Carrier. •

Modulation Amplitude Modulation (AM). • AM signals consist of three components: • Carrier. • Lower sideband. • Upper sideband. • Voice bandwidth is from 300 Hz to 3 k. Hz. • AM bandwidth is twice the voice bandwidth.

Modulation Amplitude Modulation (AM). • The sound waves that make up your voice are

Modulation Amplitude Modulation (AM). • The sound waves that make up your voice are a complex mixture of multiple frequencies. • When this complex mixture is added to the carrier, two sidebands are created that are mirror images.

Modulation Amplitude Modulation (AM).

Modulation Amplitude Modulation (AM).

Modulation Single Sideband (SSB). • AM is made up of identical mirror image sidebands

Modulation Single Sideband (SSB). • AM is made up of identical mirror image sidebands plus a carrier.

Modulation Single Sideband (SSB). • We can improve the efficiency of transmission by transmitting

Modulation Single Sideband (SSB). • We can improve the efficiency of transmission by transmitting only one sideband then reconstruct the missing sideband & carrier at the receiver.

Modulation Single Sideband (SSB). • Used for nearly all HF voice communications. • Used

Modulation Single Sideband (SSB). • Used for nearly all HF voice communications. • Used for most HF digital mode transmissions. • Used for weak-signal VHF & UHF voice communications. • Frequencies above 14 MHz typically use USB. • Frequencies below 7. 3 MHz typically use LSB. • Exception: 5 MHZ must use USB.

T 8 A 01 -- Which of the following is a form of amplitude

T 8 A 01 -- Which of the following is a form of amplitude modulation? A. B. C. D. Spread spectrum Packet radio Single sideband Phase shift keying (PSK)

Modulation Frequency Modulation (FM) • If we vary the frequency of the carrier in

Modulation Frequency Modulation (FM) • If we vary the frequency of the carrier in step with the information waveform, FM is produced.

Modulation Frequency Modulation • FM signals are much more resistant to the effects of

Modulation Frequency Modulation • FM signals are much more resistant to the effects of noise but require more bandwidth. • FM bandwidth (for voice) is between 10 and 15 k. Hz.

Modulation Phase Modulation • If we vary the phase of the carrier in step

Modulation Phase Modulation • If we vary the phase of the carrier in step with the information waveform, PM is produced. • PM signals are a lot like FM signals. • In FM, the amount of deviation is dependent only on the amplitude of the modulating signal. • In PM, the amount of deviation is dependent on both the amplitude and the frequency of the modulating signal.

Modulation Frequency/Phase Modulation • Most common voice mode on VHF & UHF. • Used

Modulation Frequency/Phase Modulation • Most common voice mode on VHF & UHF. • Used by VHF & UHF voice repeaters. • Used for VHF & UHF packet operations.

T 8 A 02 -- What type of modulation is most commonly used for

T 8 A 02 -- What type of modulation is most commonly used for VHF packet radio transmissions? A. B. C. D. FM SSB AM PSK

T 8 A 04 -- Which type of modulation is most commonly used for

T 8 A 04 -- Which type of modulation is most commonly used for VHF and UHF voice repeaters? A. B. C. D. AM SSB PSK FM

Modulation Bandwidth of Modulated Signals Type of Signal Typical Bandwidth AM Voice 6 k.

Modulation Bandwidth of Modulated Signals Type of Signal Typical Bandwidth AM Voice 6 k. Hz AM Broadcast 10 k. Hz Analog TV 6 MHz SSB Voice 2 k. Hz to 3 k. Hz SSB Digital <100 Hz to 3 k. Hz CW 150 Hz FM Voice 10 k. Hz to 15 k. Hz FM Broadcast 180 k. Hz

Modulation Bandwidth of Modulated Signals • SSB has less bandwidth than AM or FM/PM.

Modulation Bandwidth of Modulated Signals • SSB has less bandwidth than AM or FM/PM. • Therefore, less noise & better reception of weak signals. • Contesters and DX’ers normally use SSB for VHF/UHF voice contacts.

Modulation Bandwidth of Modulated Signals • CW has the narrowest bandwidth & is used

Modulation Bandwidth of Modulated Signals • CW has the narrowest bandwidth & is used for extremely weak signal work. • e. g. – EME. • Some of the newer digital modes were designed for weak signal reception and can outperform CW. • e. g. – JT 65 & FT 8.

T 8 A 03 -- Which type of voice mode is most often used

T 8 A 03 -- Which type of voice mode is most often used for long-distance (weak signal) contacts on the VHF and UHF bands? A. B. C. D. FM DRM SSB PM

T 8 A 05 -- Which of the following types of emission has the

T 8 A 05 -- Which of the following types of emission has the narrowest bandwidth? A. B. C. D. FM voice SSB voice CW Slow-scan TV

T 8 A 06 -- Which sideband is normally used for 10 meter HF,

T 8 A 06 -- Which sideband is normally used for 10 meter HF, VHF, and UHF single-sideband communications? A. B. C. D. Upper sideband Lower sideband Suppressed sideband Inverted sideband

T 8 A 07 -- What is an advantage of single sideband (SSB) over

T 8 A 07 -- What is an advantage of single sideband (SSB) over FM for voice transmissions? A. B. C. D. SSB signals are easier to tune SSB signals are less susceptible to interference SSB signals have narrower bandwidth All of these choices are correct

T 8 A 08 -- What is the approximate bandwidth of a single sideband

T 8 A 08 -- What is the approximate bandwidth of a single sideband (SSB) voice signal? A. B. C. D. 1 k. Hz 3 k. Hz 6 k. Hz 15 k. Hz

T 8 A 09 -- What is the approximate bandwidth of a VHF repeater

T 8 A 09 -- What is the approximate bandwidth of a VHF repeater FM phone signal? A. B. C. D. Less than 500 Hz About 150 k. Hz Between 10 and 15 k. Hz Between 50 and 125 k. Hz

T 8 A 10 -- What is the typical bandwidth of analog fast-scan TV

T 8 A 10 -- What is the typical bandwidth of analog fast-scan TV transmissions on the 70 centimeter band? A. B. C. D. More than 10 MHz About 6 MHz About 3 MHz About 1 MHz

T 8 A 11 -- What is the approximate maximum bandwidth required to transmit

T 8 A 11 -- What is the approximate maximum bandwidth required to transmit a CW signal? A. B. C. D. 2. 4 k. Hz 150 Hz 1000 Hz 15 k. Hz

Transmitters and Receivers Selecting Band, Frequency and Mode. • Selecting the band. • Usually

Transmitters and Receivers Selecting Band, Frequency and Mode. • Selecting the band. • Usually two or more buttons to select the band. • Several buttons labeled in frequency (MHz), or • Several buttons labeled in wavelength (m or cm), or • 2 buttons (Band Up & Band Down).

Transmitters and Receivers Selecting Band, Frequency and Mode. Frequency (MHz) Wavelength (m or cm)

Transmitters and Receivers Selecting Band, Frequency and Mode. Frequency (MHz) Wavelength (m or cm) 1. 8 160 m 50 6 m 3. 5 80 m 144 2 m 7 40 m 222 1. 25 m 10 30 m 420 70 cm 14 20 m 902 33 m 18 17 m 1240 23 m 21 15 m 2300 13 m 24 12 m 28 10 m

Transmitters and Receivers Selecting Band, Frequency and Mode. • Selecting the frequency. • Tuning

Transmitters and Receivers Selecting Band, Frequency and Mode. • Selecting the frequency. • Tuning knob. • Select frequency. • VFO (variable-frequency oscillator). • Dial-in any frequency within the range of the radio. • Select memory channel. • Most rigs have memory channels you can use to rapidly select your favorite frequencies. • Keypad. • Direct entry of frequency or memory channel.

Transmitters and Receivers Selecting Band, Frequency and Mode. • Selecting the mode. • Usually

Transmitters and Receivers Selecting Band, Frequency and Mode. • Selecting the mode. • Usually several buttons to select the desired mode. • Occasionally one button that cycles through all of the modes. • Compact radios designed for mobile use. • Often modes are “paired”. • LSB – USB. • AM – FM. • CW – RTTY.

Transmitters and Receivers Selecting Band, Frequency and Mode. • Watch that band edge! •

Transmitters and Receivers Selecting Band, Frequency and Mode. • Watch that band edge! • All transceiver VFOs have some calibration error. • All transceiver VFOs can drift in frequency. • All transmitted signals have components that extend above and/or below the carrier frequency. • These components are called sidebands.

Transmitters and Receivers Selecting Band, Frequency and Mode. • Watch that band edge! •

Transmitters and Receivers Selecting Band, Frequency and Mode. • Watch that band edge! • Your ENTIRE signal must be within the band. • DO NOT set your transmit frequency exactly on the band edge or your sidebands may fall outside of the band.

T 1 B 09 -- Why should you not set your transmit frequency to

T 1 B 09 -- Why should you not set your transmit frequency to be exactly at the edge of an amateur band or sub-band? A. To allow for calibration error in the transmitter frequency display B. So that modulation sidebands do not extend beyond the band edge C. To allow for transmitter frequency drift D. All of these choices are correct

T 4 B 02 -- Which of the following can be used to enter

T 4 B 02 -- Which of the following can be used to enter the operating frequency on a modern transceiver? A. B. C. D. The keypad or VFO knob The CTCSS or DTMF encoder The Automatic Frequency Control All of these choices are correct

T 4 B 04 -- What is a way to enable quick access to

T 4 B 04 -- What is a way to enable quick access to a favorite frequency on your transceiver? A. B. C. D. Enable the CTCSS tones Store the frequency in a memory channel Disable the CTCSS tones Use the scan mode to select the desired frequency

Transmitters and Receivers Transmitter Functions. • Output power level. • Continuously-variable control. • Most

Transmitters and Receivers Transmitter Functions. • Output power level. • Continuously-variable control. • Most SSB/CW transceivers. • 2, 3, or 4 pre-set levels. • Most VHF/UHF FM transceivers.

Transmitters and Receivers Transmitter Functions. • Switching transceiver from receive to transmit. • Normally

Transmitters and Receivers Transmitter Functions. • Switching transceiver from receive to transmit. • Normally done manually using a push-to-talk switch referred to as the PTT switch. • Push button on hand microphone. • Foot switch. • Hand switch.

Transmitters and Receivers Transmitter Functions. • Switching transceiver from receive to transmit. • Can

Transmitters and Receivers Transmitter Functions. • Switching transceiver from receive to transmit. • Can be done automatically using a voice operated circuit referred to as VOX. • Built into most HF transceivers. . • Not normally found in FM transceivers.

Transmitters and Receivers Transmitter Functions. • Microphone gain. • Speech processor. • Increases average

Transmitters and Receivers Transmitter Functions. • Microphone gain. • Speech processor. • Increases average transmitter power output by compressing the modulating signal. • Without compression, average power is about 25% of PEP. • With compression, average power is about 40% of PEP. • Common on most SSB transceivers. • Not normally used on FM transmitters.

Transmitters and Receivers Transmitter Functions. • Microphones. • Hand microphone. • Usually supplied with

Transmitters and Receivers Transmitter Functions. • Microphones. • Hand microphone. • Usually supplied with transceiver. • Normally has PTT switch. • May have power for auxiliary functions. • Keypad, frequency control, etc. • Desk microphone. • PTT switch on base and/or post. • Headset. • Hand switch, foot switch, or VOX for PTT.

Transmitters and Receivers Transmitter Functions. • CW key. • When operating CW, the transceiver

Transmitters and Receivers Transmitter Functions. • CW key. • When operating CW, the transceiver automatically switches to transmit when the key contacts are closed. • The dots (dits) and dashes (dahs) that form the Morse code caharaters are called elements. • When the operator forms the elements of the code manually, it is called hand keying. • The operator can be assisted in forming the elements by using special types of keys.

Transmitters and Receivers Transmitter Functions. • CW key. • Straight key. • Semi-automatic key.

Transmitters and Receivers Transmitter Functions. • CW key. • Straight key. • Semi-automatic key. • “Bug”. • Automatic key. • Paddles. • Electronic keyer. • Built into most HF transceivers. • Keyboard.

Transmitters and Receivers Transmitter Functions. • Dummy load. • A dummy load is a

Transmitters and Receivers Transmitter Functions. • Dummy load. • A dummy load is a non-radiating replacement for your antenna. Used while tuning or testing your transmitter to avoid interfering with other stations. • 50Ω non-inductive resistor mounted in some sort of container to dissipate heat.

T 7 A 07 -- What is meant by “PTT”? A. Pre-transmission tuning to

T 7 A 07 -- What is meant by “PTT”? A. Pre-transmission tuning to reduce transmitter harmonic emission B. Precise tone transmissions used to limit repeater access to only certain signals C. A primary transformer tuner use to match antennas D. The push-to-talk function that switches between receive and transmit

T 7 C 01 -- What is the primary purpose of a dummy load?

T 7 C 01 -- What is the primary purpose of a dummy load? A. To prevent transmitting signals over the air when making tests B. To prevent over-modulation of a transmitter C. To improve the efficiency of an antenna D. To improve the signal-to-noise ratio of a receiver

T 7 C 12 -- What does a dummy load consist of? A. B.

T 7 C 12 -- What does a dummy load consist of? A. B. C. D. A high-gain amplifier and a TR switch A non-inductive resistor and a heat sink A low-voltage power supply and a DC relay A 50 ohm reactance used to terminate a transmission line

T 8 D 14 -- What is an electronic keyer? A. A device for

T 8 D 14 -- What is an electronic keyer? A. A device for switching antennas from transmit to receive B. A device for voice activated switching from receive to transmit C. A device that assists in manual sending of Morse code D. An interlock to prevent unauthorized use of a radio

Transmitters and Receivers Spurious Signals. § 97. 3(a)(43) Spurious emission. An emission, or frequencies

Transmitters and Receivers Spurious Signals. § 97. 3(a)(43) Spurious emission. An emission, or frequencies outside the necessary bandwidth of a transmission, the level of which may be reduced without affecting the information being transmitted.

Transmitters and Receivers Spurious Signals. • Overmodulation. • SSB & AM. • Too high

Transmitters and Receivers Spurious Signals. • Overmodulation. • SSB & AM. • Too high a microphone gain setting causing distortion. • Results in strong signals outside of the normal 3 k. Hz voice bandwidth. • a. k. a. – Splatter. • ALC circuit helps prevent splatter. • Reduces peak amplitude of voice signal. • Digital signals are distorted when ALC activates.

Transmitters and Receivers Spurious Signals. • Overmodulation. • • FM. Similar to overmodulation of

Transmitters and Receivers Spurious Signals. • Overmodulation. • • FM. Similar to overmodulation of SSB & AM signals. Causes excessive bandwidth. Can cause complete loss of received signal under certain conditions.

Transmitters and Receivers Spurious Signals. • RF Feedback. • Can cause spurious signals that

Transmitters and Receivers Spurious Signals. • RF Feedback. • Can cause spurious signals that sound similar to overmodulation.

Transmitters and Receivers Spurious Signals. • CW key clicks. • Clicking sounds heard at

Transmitters and Receivers Spurious Signals. • CW key clicks. • Clicking sounds heard at some distance above and below the transmit frequency. • Caused by too rapid rise & fall times when carrier is turned on and off. 2 ms Rise/Fall Times 8 ms Rise/Fall Times

T 2 B 05 -- What might be the problem if a repeater user

T 2 B 05 -- What might be the problem if a repeater user says your transmissions are breaking up on voice peaks? A. B. C. D. You have the incorrect offset You need to talk louder You are talking too loudly Your transmit power is too high

T 4 B 01 -- What may happen if a transmitter is operated with

T 4 B 01 -- What may happen if a transmitter is operated with the microphone gain set too high? A. B. C. D. The output power might be too high The output signal might become distorted The frequency might vary The SWR might increase

T 7 B 01 -- What can you do if you are told your

T 7 B 01 -- What can you do if you are told your FM handheld or mobile transceiver is overdeviating? A. B. C. D. Talk louder into the microphone Let the transceiver cool off Change to a higher power level Talk farther away from the microphone

Transmitters and Receivers Receiver Functions. • AF gain. • a. k. a – Audio

Transmitters and Receivers Receiver Functions. • AF gain. • a. k. a – Audio gain. • Volume control.

Transmitters and Receivers Receiver Functions. • Automatic gain control (AGC). • Due to propagation

Transmitters and Receivers Receiver Functions. • Automatic gain control (AGC). • Due to propagation changes, the received strength of a signal will vary up and down. • For AM modes, as the signal strength varies, the audio output volume will vary accordingly.

Transmitters and Receivers Receiver Functions. • Automatic gain control (AGC). • AGC automatically adjusts

Transmitters and Receivers Receiver Functions. • Automatic gain control (AGC). • AGC automatically adjusts the RF gain of the receiver in an attempt to keep the audio output relatively constant. • A voltage is created based on signal strength to control gain. • Normally, the S-meter reading is derived from the AGC voltage. • Different modes require different AGC response speeds. • CW & data requires faster response speed. • Voice signals require slower response speed.

Transmitters and Receivers Receiver Functions. • RF gain. • Adjusts gain of receiver by

Transmitters and Receivers Receiver Functions. • RF gain. • Adjusts gain of receiver by changing the AGC voltage. • Turning RF gain down results in a higher S-meter reading. • Pre-amplifier. • Pre-amp needed on higher-frequency bands. • Pre-amp may do more harm than good on lowerfrequency bands. • Sometimes a switch to turn pre-amp on/off or add attenuation.

Transmitters and Receivers Receiver Functions. • Squelch. • Silences receiver audio when no signal

Transmitters and Receivers Receiver Functions. • Squelch. • Silences receiver audio when no signal present. • Carrier squelch. • Silences audio based solely on the absence of an RF signal. • Most effective with FM signals. • Tone squelch. • Silences audio based on the absence of a sub-audible tone. • Continuous tone coded squelch system (CTCSS). • a. k. a. – PL (Private Line®) tone. • Commonly used on VHF or UHF FM repeaters.

T 4 B 03 -- What is the purpose of the squelch control on

T 4 B 03 -- What is the purpose of the squelch control on a transceiver? A. B. C. D. To set the highest level of volume desired To set the transmitter power level To adjust the automatic gain control To mute receiver output noise when no signal is being received

T 4 B 11 -- What is the function of automatic gain control, or

T 4 B 11 -- What is the function of automatic gain control, or AGC? A. B. C. D. To keep received audio relatively constant To protect an antenna from lightning To eliminate RF on the station cabling An asymmetric goniometer control used for antenna matching

Transmitters and Receivers Receiver Functions. • Sensitivity and Selectivity. • Sensitivity is a measure

Transmitters and Receivers Receiver Functions. • Sensitivity and Selectivity. • Sensitivity is a measure of how weak a signal the receiver can receive. • Sensitivity may be improved by installing a pre-amplifier (preamp) between the antenna and the receiver. • Often built into the receiver. • Selectivity is a measure of how well the receiver rejects signals near the desired frequency. • Determined by the receiver filters.

T 7 A 01 -- Which term describes the ability of a receiver to

T 7 A 01 -- Which term describes the ability of a receiver to detect the presence of a signal? A. B. C. D. Linearity Sensitivity Selectivity Total Harmonic Distortion

T 7 A 04 -- Which term describes the ability of a receiver to

T 7 A 04 -- Which term describes the ability of a receiver to discriminate between multiple signals? A. B. C. D. Discrimination ratio Sensitivity Selectivity Harmonic distortion

T 7 A 11 -- Where is an RF preamplifier installed? A. B. C.

T 7 A 11 -- Where is an RF preamplifier installed? A. B. C. D. Between the antenna and receiver At the output of the transmitter's power amplifier Between a transmitter and antenna tuner At the receiver's audio output

Transmitters and Receivers Receiver Functions. • Filtering and tuning. • Receivers reject unwanted nearby

Transmitters and Receivers Receiver Functions. • Filtering and tuning. • Receivers reject unwanted nearby signals by using bandpass filters. • Want to match filter width to bandwidth of signal. • Reduces interference from nearby signals. • Reduces noise level. Mode Typical Filter Width CW 500 Hz or less RTTY 500 Hz SSB 2. 4 k. Hz to 3. 0 k. Hz Digital 3 k. Hz to 4 k. Hz AM 6 k. Hz to 8 k. Hz FM 15 k. Hz

Transmitters and Receivers Receiver Functions. • Filtering and tuning. • Receiver incremental tuning (RIT).

Transmitters and Receivers Receiver Functions. • Filtering and tuning. • Receiver incremental tuning (RIT). • a. k. a. – Clarifier. • Allows small changes in receive frequency without changing transmit frequency. • Transmitter incremental tuning (XIT). • Allows small changes in transmit frequency without changing receive frequency.

Transmitters and Receivers Receiver Functions. • Noise blanker. • Detects presence of a noise

Transmitters and Receivers Receiver Functions. • Noise blanker. • Detects presence of a noise pulse & turns off (blanks) the receiver audio during the pulse. • Especially effective on repetitive pulse-type noise. • Ignition noise. • Electric motors. • Fluorescent lamps.

Transmitters and Receivers Receiver Functions. • Noise limiter. • Clamps receiver audio at a

Transmitters and Receivers Receiver Functions. • Noise limiter. • Clamps receiver audio at a maximum level. • Prevents a strong noise burst from damaging your hearing. • Notch filter. • A very narrow band reject filter used to eliminate an interfering steady signal, such as a carrier. • Do NOT use with CW or data.

Transmitters and Receivers Receiver Functions. • Signal Strength. • Most receivers have a method

Transmitters and Receivers Receiver Functions. • Signal Strength. • Most receivers have a method of displaying signal strength. • Analog Meter. • LCD display. • Often derived from AGC voltage & not well calibrated.

Transmitters and Receivers Receiver Functions. • Signal Strength. • S-Units • Numbered S 1

Transmitters and Receivers Receiver Functions. • Signal Strength. • S-Units • Numbered S 1 (weakest) to S 9 (strongest). • 1 S-unit = 6 d. B. • S 9 is defined as 50μV (-73 d. Bm) at the antenna terminals. • Extremely strong signals are reported as the number of d. B greater than S 9. • e. g. – “Your signal is 10 d. B over S 9. ”

T 4 B 05 -- Which of the following would reduce ignition interference to

T 4 B 05 -- Which of the following would reduce ignition interference to a receiver? A. B. C. D. Change frequency slightly Decrease the squelch setting Turn on the noise blanker Use the RIT control

T 4 B 06 -- Which of the following controls could be used if

T 4 B 06 -- Which of the following controls could be used if the voice pitch of a single-sideband signal seems too high or low? A. B. C. D. The AGC or limiter The bandwidth selection The tone squelch The receiver RIT or clarifier

T 4 B 07 -- What does the term “RIT” mean? A. B. C.

T 4 B 07 -- What does the term “RIT” mean? A. B. C. D. Receiver Input Tone Receiver Incremental Tuning Rectifier Inverter Test Remote Input Transmitter

T 4 B 08 -- What is the advantage of having multiple receive bandwidth

T 4 B 08 -- What is the advantage of having multiple receive bandwidth choices on a multimode transceiver? A. Permits monitoring several modes at once B. Permits noise or interference reduction by selecting a bandwidth matching the mode C. Increases the number of frequencies that can be stored in memory D. Increases the amount of offset between receive and transmit frequencies

T 4 B 09 -- Which of the following is an appropriate receive filter

T 4 B 09 -- Which of the following is an appropriate receive filter bandwidth for minimizing noise and interference for SSB reception? A. B. C. D. 500 Hz 1000 Hz 2400 Hz 5000 Hz

T 4 B 10 -- Which of the following is an appropriate receive filter

T 4 B 10 -- Which of the following is an appropriate receive filter bandwidth for minimizing noise and interference for CW reception? A. B. C. D. 500 Hz 1000 Hz 2400 Hz 5000 Hz

T 4 B 11 -- What is the function of automatic gain control, or

T 4 B 11 -- What is the function of automatic gain control, or AGC? A. B. C. D. To keep received audio relatively constant To protect an antenna from lightning To eliminate RF on the station cabling An asymmetric goniometer control used for antenna matching

T 4 B 12 -- Which of the following could be used to remove

T 4 B 12 -- Which of the following could be used to remove power line noise or ignition noise? A. B. C. D. Squelch Noise blanker Notch filter All of these choices are correct

Break

Break

Transmitters and Receivers VHF/UHF Power Amplifiers. • Hand-held FM transceivers are very popular, but

Transmitters and Receivers VHF/UHF Power Amplifiers. • Hand-held FM transceivers are very popular, but relatively low power. • Typically 8 watts or less. • You can use an external power amplifier to increase the transmitter power output.

Transmitters and Receivers VHF/UHF Power Amplifiers. • Multi-mode amplifiers need to operate slightly differently

Transmitters and Receivers VHF/UHF Power Amplifiers. • Multi-mode amplifiers need to operate slightly differently depending on mode and include an SSB/CW-FM switch. • SSB position. • Required for SSB operations. • Best linearity, but less efficient. • CW-FM position. • Used for CW & FM operations. • Best efficiency, but poorer linearity.

T 7 A 09 -- What is the function of the SSB/CWFM switch on

T 7 A 09 -- What is the function of the SSB/CWFM switch on a VHF power amplifier? A. Change the mode of the transmitted signal B. Set the amplifier for properation in the selected mode C. Change the frequency range of the amplifier to operate in the proper portion of the band D. Reduce the received signal noise

T 7 A 10 -- What device increases the low-power output from a handheld

T 7 A 10 -- What device increases the low-power output from a handheld transceiver? A. B. C. D. A voltage divider An RF power amplifier An impedance network All of these choices are correct

Transmitters and Receivers Transverters. • Convert a transceiver’s transmit & receive frequency range to

Transmitters and Receivers Transverters. • Convert a transceiver’s transmit & receive frequency range to an entirely new band. • Use mixers. • Low-power transmit signals shifted to new band. • Receive converter allows signals on new band to be heard. • Usually used to shift the 10 m band of an HF transceiver to VHF/UHF/Microwave frequencies.

T 7 A 06 -- What device converts the RF input and output of

T 7 A 06 -- What device converts the RF input and output of a transceiver to another band? A. B. C. D. High-pass filter Low-pass filter Transverter Phase converter

Digital Communications Most HF & some VHF/UHF stations include a computer to: • Automate

Digital Communications Most HF & some VHF/UHF stations include a computer to: • Automate many functions. • Frequency & mode control. • Sending/receiving CW. • International Morse Code. • Logging & award tracking. • QSL’ing. • Allow types of operation not otherwise possible. • Digital modes.

Digital Communications DXLabs Suite • Radio control. • Logging. • QSL’ing. • Award tracking.

Digital Communications DXLabs Suite • Radio control. • Logging. • QSL’ing. • Award tracking. • DX spots. • Propagation prediction. • CW, RTTY, & PSK 31.

T 4 A 02 -- How might a computer be used as part of

T 4 A 02 -- How might a computer be used as part of an amateur radio station? A. B. C. D. For logging contacts and contact information For sending and/or receiving CW For generating and decoding digital signals All of these choices are correct

T 8 D 09 -- What code is used when sending CW in the

T 8 D 09 -- What code is used when sending CW in the amateur bands? A. B. C. D. Baudot Hamming International Morse All of these choices are correct

Digital Communications Amateur Digital Modes. • Amateur transceivers designed for voice transmission can be

Digital Communications Amateur Digital Modes. • Amateur transceivers designed for voice transmission can be used to send digital information (data) as a series of tones. • Data modes consist of: • Modulation method. • How tones are added to RF signal. • Protocol. • Rules governing how data is converted to tones.

Digital Communications Amateur Digital Modes. • Many digital modes have error detection and correction

Digital Communications Amateur Digital Modes. • Many digital modes have error detection and correction features built into the protocol. • Forward Error Correction (FEC). • Adds extra information so that data can be reconstructed. • e. g. - MFSK 16, MT 63. • Automatic Repeat Request (ARQ). • If error detected, asks sending station to retransmit data. • e. g. – Pa. cket, Winmor

Digital Communications Data Modes. • CW is actually a “digital” mode. • Amplitude modulation

Digital Communications Data Modes. • CW is actually a “digital” mode. • Amplitude modulation (AM). • International Morse Code. • Letters A-Z • No lower case. • Numerals 0 -9. • Some punctuation. • Some special characters.

Digital Communications Amateur Digital Modes. • Radioteletype (RTTY). • Oldest digital mode. • Adapted

Digital Communications Amateur Digital Modes. • Radioteletype (RTTY). • Oldest digital mode. • Adapted from land-line teletype system. • Frequency shift keying (FSK). • Audio frequency shift keying (AFSK). • 5 -bit Baudot code. • Letters A-Z • No lower case. • Numbers 0 -9. • Some punctuation.

Digital Communications Amateur Digital Modes. • Packet. • American Standard Code for Information Interchange

Digital Communications Amateur Digital Modes. • Packet. • American Standard Code for Information Interchange (ASCII) code. • • Start bit. 7 data bits. Parity bit (may be 8 th data bit). 1, 1. 5, or 2 stop bits. Upper & lower case letters. Numerals 0 -9. Punctuation & control codes.

Digital Communications Amateur Digital Modes. • MFSK. • Multi-tone frequency shift keying. • Forward

Digital Communications Amateur Digital Modes. • MFSK. • Multi-tone frequency shift keying. • Forward error correction (FEC). • Extra information sent to allow reconstruction of original data in the presence of data.

Digital Communications Amateur Digital Modes. • Olivia. • Variation of MFSK. • Very effective

Digital Communications Amateur Digital Modes. • Olivia. • Variation of MFSK. • Very effective at poor signal-to-noise levels. • S/N = -14 d. B. • Relatively slow but robust.

Digital Communications Amateur Digital Modes. • AMTOR. • Variation of RTTY. • • 170

Digital Communications Amateur Digital Modes. • AMTOR. • Variation of RTTY. • • 170 Hz FSK. 100 baud. Special code. Adds ARQ error correction. • Rarely used anymore. • Replaced by more modern modes.

Digital Communications Amateur Digital Modes. • PACTOR. • Developed by Special Communications Systems Gm.

Digital Communications Amateur Digital Modes. • PACTOR. • Developed by Special Communications Systems Gm. BH. • Combination of AMTOR & Packet. • PACTOR I. • Open technology Relatively inexpensive modems. • $50. 00 to $150. 00. • PACTOR II, PACTOR III, & PACTOR IV. • Proprietary technology Very expensive modems. • $1000. 00 to >$1600. • Used in NTS digital message handling system.

Digital Communications Amateur Digital Modes. • WINMOR. • Similar to PACTOR. • Developed as

Digital Communications Amateur Digital Modes. • WINMOR. • Similar to PACTOR. • Developed as inexpensive alternate to PACTOR. • Uses ARQ error correction. • Only a simple soundcard interface is required. • Intended for handling the HF portion of the Win. Link system.

Digital Communications Amateur Digital Modes. • The WSJT Modes. • A family of modes

Digital Communications Amateur Digital Modes. • The WSJT Modes. • A family of modes designed for special types of communications. • FSK 441 – Meteor scatter (2 m & 70 cm). • JT 6 M – Meteor scatter (6 m). • JT 65 – VHF & UHF moonbounce or earth-moon-earth (EME). • JT 65 -HF – HF weak signals many d. B below the noise. • JT 9 – MF & HF weak signals. • FT 8 – MF & VHF weak signals. • DXpedition mode.

Digital Communications Amateur Digital Modes. • Wi-Fi and Broadband-Hamnet™. • Wi-fi (IEEE 802. 11)

Digital Communications Amateur Digital Modes. • Wi-Fi and Broadband-Hamnet™. • Wi-fi (IEEE 802. 11) shares frequencies with the Amateur Radio Service in the 2. 4 GHz & 5. 6 GHz bands. • Amateurs have modified the firmware of some commercial wi-fi modems to automatically connect forming a local network. • Broadband-Hamnet™. • High Speed Multi-Media Network (HSMM). • Useful in public service & emergency communications.

T 8 D 01 -- Which of the following is a digital communications mode?

T 8 D 01 -- Which of the following is a digital communications mode? A. B. C. D. Packet radio IEEE 802. 11 JT 65 All of these choices are correct

T 8 D 10 -- Which of the following operating activities is supported by

T 8 D 10 -- Which of the following operating activities is supported by digital mode software in the WSJT suite? A. B. C. D. Moonbounce or Earth-Moon-Earth Weak-signal propagation beacons Meteor scatter All of these choices are correct

T 8 D 12 -- Which of the following best describes Broadband-Hamnet(TM), also referred

T 8 D 12 -- Which of the following best describes Broadband-Hamnet(TM), also referred to as a high-speed multi-media network? A. An amateur-radio-based data network using commercial Wi-Fi gear with modified firmware B. A wide-bandwidth digital voice mode employing DRM protocols C. A satellite communications network using modified commercial satellite TV hardware D. An internet linking protocol used to network repeaters

T 8 D 13 -- What is FT 8? A. A wideband FM voice

T 8 D 13 -- What is FT 8? A. A wideband FM voice mode B. A digital mode capable of operating in low signal-tonoise conditions that transmits on 15 -second intervals C. An eight channel multiplex mode for FM repeaters D. A digital slow scan TV mode with forward error correction and automatic color compensation

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • Oldest of “modern”

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • Oldest of “modern” digital modes. • Development started in 1970’s. • Became widely popular in 1980’s. • Still popular on VHF & UHF. • 1200 -9600 baud on 2 m. • Not practical on HF. • Limited to 300 baud. • Very slow when band conditions are noisy.

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • Data is sent

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • Data is sent in groups of characters called packets. • AX. 25 protocol. • Each packet has 5 parts, in this order: 1. 2. 3. 4. 5. Start of packet flag character. Header (address & control information). Data (1 to 256 characters). Checksum. End of packet flag character.

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • The checksum is

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • The checksum is used to detect errors in the received message. • If an error is detected, the receiving station requests the transmitting station to send the packet again. • This is called Automatic Repeat Request (ARQ). • Message will either be received error-free or not at all.

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • A hardware device

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • A hardware device called a Terminal Node Controller (TNC) handles all details of the protocol. • The computer sends data to TNC & TNC sends properly formatted packets to the radio. • The radio sends packets to the TNC & TNC sends data to the computer. • A TNC can be emulated in software.

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • A TNC can

Digital Communications Amateur Digital Modes. • Packet and Packet Networks. • A TNC can be set up to act as a digipeater. • Analogous to a voice repeater but not real-time. • Uses a store-and-forward technique. • A packet is received and then immediately re-transmitted.

T 8 D 08 -- Which of the following may be included in packet

T 8 D 08 -- Which of the following may be included in packet transmissions? A. A check sum that permits error detection B. A header that contains the call sign of the station to which the information is being sent C. Automatic repeat request in case of error D. All of these choices are correct

T 8 D 11 -- What is an ARQ transmission system? A. A special

T 8 D 11 -- What is an ARQ transmission system? A. A special transmission format limited to video signals B. A system used to encrypt command signals to an amateur radio satellite C. A digital scheme whereby the receiving station detects errors and sends a request to the sending station to retransmit the information D. A method of compressing the data in a message so more information can be sent in a shorter time

Digital Communications Amateur Digital Modes. • Keyboard-to-Keyboard. • Modes designed for real-time, person-to-person communications

Digital Communications Amateur Digital Modes. • Keyboard-to-Keyboard. • Modes designed for real-time, person-to-person communications are called keyboard-to-keyboard modes. • Not for sending data or files. • Nearly all digital modes can be used. • The most popular keyboard-to-keyboard mode today is PSK 31.

Digital Communications Amateur Digital Modes. • PSK 31. • • PSK = Phase shift

Digital Communications Amateur Digital Modes. • PSK 31. • • PSK = Phase shift keying. 31 = 31. 25 baud. Narrowest bandwidth of any mode, including CW. Very effective in noisy conditions.

T 8 D 06 -- What does the abbreviation "PSK" mean? A. B. C.

T 8 D 06 -- What does the abbreviation "PSK" mean? A. B. C. D. Pulse Shift Keying Phase Shift Keying Packet Short Keying Phased Slide Keying

Digital Communications Amateur Digital Modes. • APRS stands for “Automatic Packet Reporting System“. •

Digital Communications Amateur Digital Modes. • APRS stands for “Automatic Packet Reporting System“. • • Developed by Bob Bruninga, WB 4 APR. Uses packet radio (144. 390 MHz in North America). Often connected to a GPS receiver for position tracking. Also can be used for messaging.

Digital Communications Amateur Digital Modes. • APRS. • Digipeaters are used to relay RF

Digital Communications Amateur Digital Modes. • APRS. • Digipeaters are used to relay RF signals to or from an internet gateway. • An internet gateway transfers packets between RF & the internet. • Non-radio uses. • Often personal weather stations are connected to the APRS network on the internet for automated weather data gathering.

Digital Communications Amateur Digital Modes. • APRS.

Digital Communications Amateur Digital Modes. • APRS.

T 8 D 02 -- What does the term “APRS” mean? A. B. C.

T 8 D 02 -- What does the term “APRS” mean? A. B. C. D. Automatic Packet Reporting System Associated Public Radio Station Auto Planning Radio Set-up Advanced Polar Radio System

T 8 D 03 -- Which of the following devices is used to provide

T 8 D 03 -- Which of the following devices is used to provide data to the transmitter when sending automatic position reports from a mobile amateur radio station? A. B. C. D. The vehicle speedometer A WWV receiver A connection to a broadcast FM sub-carrier receiver A Global Positioning System receiver

T 8 D 05 -- Which of the following is an application of APRS

T 8 D 05 -- Which of the following is an application of APRS (Automatic Packet Reporting System)? A. Providing real-time tactical digital communications in conjunction with a map showing the locations of stations B. Showing automatically the number of packets transmitted via PACTOR during a specific time interval C. Providing voice over internet connection between repeaters D. Providing information on the number of stations signed into a repeater

Digital Communications Setting Up for Digital Modes. • Need some way to: • •

Digital Communications Setting Up for Digital Modes. • Need some way to: • • • Convert data to tones. Feed tones to radio. Key the radio. Receive tones from radio. Convert tones to data. • Can use: • External modulator-demodulator (modem). • Soundcard software.

Digital Communications Setting Up for Digital Modes. • Modulator-demodulator (modem). • External device to

Digital Communications Setting Up for Digital Modes. • Modulator-demodulator (modem). • External device to convert data to tones for transmission and to convert tones to data for reception. • Connects between computer serial port and radio. • Packet Terminal Node Controller (TNC). • Multi-mode controller. • Limited to just a few modes.

Digital Communications Setting Up for Digital Modes. • Soundcard software. • Computer program that

Digital Communications Setting Up for Digital Modes. • Soundcard software. • Computer program that uses computer soundcard to send/receive the tones. • Requires hardware interface to connect computer soundcard to radio microphone & speaker connections, and to connect serial port to PTT. • Some radios have a data connector which makes connections easier. • Allows operating all of the various digital modes.

Digital Communications Setting Up for Digital Modes. • Soundcard interface.

Digital Communications Setting Up for Digital Modes. • Soundcard interface.

Digital Communications Setting Up for Digital Modes.

Digital Communications Setting Up for Digital Modes.

T 4 A 04 -- Which computer sound card port is connected to a

T 4 A 04 -- Which computer sound card port is connected to a transceiver’s headphone or speaker output for operating digital modes? A. B. C. D. Headphone output Mute Microphone or line input PCI or SDI

T 4 A 06 -- Which of the following connections might be used between

T 4 A 06 -- Which of the following connections might be used between a voice transceiver and a computer for digital operation? A. Receive and transmit mode, status, and location B. Antenna and RF power C. Receive audio, transmit audio, and push-to-talk (PTT) D. NMEA GPS location and dc power

T 4 A 07 -- How is a computer’s sound card used when conducting

T 4 A 07 -- How is a computer’s sound card used when conducting digital communications? A. The sound card communicates between the computer CPU and the video display B. The sound card records the audio frequency for video display C. The sound card provides audio to the radio's microphone input and converts received audio to digital form D. All of these choices are correct

Digital Communications Gateways. • Provide connections between data transmitted via amateur radio & the

Digital Communications Gateways. • Provide connections between data transmitted via amateur radio & the internet. • • Message forwarding. Packet bulletin boards. Win. Link remote message service (RMS) stations. D-Star repeaters. CAUTION: All regulations concerning message content & appropriateness apply to messages sent via internet gateways.

T 8 C 11 -- What name is given to an amateur radio station

T 8 C 11 -- What name is given to an amateur radio station that is used to connect other amateur stations to the internet? A. B. C. D. A gateway A repeater A digipeater A beacon

Power Supplies and Batteries Power Supplies. • House power is 120 VAC, 60 Hz.

Power Supplies and Batteries Power Supplies. • House power is 120 VAC, 60 Hz. • Most modern radios require +12 VDC. • Actually +13. 8 VDC. • A power supply is a device that converts 120 VAC power to the desired DC voltage or voltages.

Power Supplies and Batteries Power Supplies. • Unregulated supply. • Simple circuit. • Voltage

Power Supplies and Batteries Power Supplies. • Unregulated supply. • Simple circuit. • Voltage can vary over a wide range with changing load current. • Not good for solid-state radios.

Power Supplies and Batteries Power Supplies. • Regulated supply. • More complex circuit. •

Power Supplies and Batteries Power Supplies. • Regulated supply. • More complex circuit. • Adds a circuit called a voltage regulator to an unregulated supply. • Voltage is nearly constant with changing load. • Radios work best with a regulated power supply.

Power Supplies and Batteries Power Supplies. • Ratings: • Output voltage. • Continuous current.

Power Supplies and Batteries Power Supplies. • Ratings: • Output voltage. • Continuous current. • How much current can be supplied over the long term. • Intermittent current. • a. k. a. – Surge current or peak current. • How much current can be supplied over the short term. • Voltage regulation. • How well the power supply can handle rapid current changes.

Power Supplies and Batteries Power Supplies. • Regulated Power Supplies. • Linear. • Large

Power Supplies and Batteries Power Supplies. • Regulated Power Supplies. • Linear. • Large & heavy. • Inefficient. • Generate heat. • Easy to repair. • Less expensive.

Power Supplies and Batteries Power Supplies. • Regulated Power Supplies. • Switching. • •

Power Supplies and Batteries Power Supplies. • Regulated Power Supplies. • Switching. • • • Small & lightweight. Very efficient. More difficult to repair. More expensive. May generate RF noise.

Power Supplies and Batteries Power Supplies. • Wire Size and Power Sources. • Transceivers

Power Supplies and Batteries Power Supplies. • Wire Size and Power Sources. • Transceivers can draw large amounts of current while transmitting. • >20 A for a 100 W HF transceiver. • Large wire sizes must be used to prevent voltage drop in the wiring. • Higher current larger wire. • Longer length larger wire.

T 4 A 01 -- What must be considered to determine the minimum current

T 4 A 01 -- What must be considered to determine the minimum current capacity needed for a transceiver's power supply? A. B. C. D. Efficiency of the transmitter at full power output Receiver and control circuit power Power supply regulation and heat dissipation All of these are correct

T 4 A 03 -- Why should wiring between the power source and radio

T 4 A 03 -- Why should wiring between the power source and radio be heavy-gauge wire and kept as short as possible? A. To avoid voltage falling below that needed for properation B. To provide a good counterpoise for the antenna C. To avoid RF interference D. All of these choices are correct

T 5 A 06 -- How much voltage does a mobile transceiver typically require?

T 5 A 06 -- How much voltage does a mobile transceiver typically require? A. B. C. D. About 12 volts About 30 volts About 120 volts About 240 volts

T 6 D 05 -- What type of circuit controls the amount of voltage

T 6 D 05 -- What type of circuit controls the amount of voltage from a power supply? A. B. C. D. Regulator Oscillator Filter Phase inverter

Power Supplies and Batteries Mobile Power Wiring. • Fuse BOTH positive & negative leads

Power Supplies and Batteries Mobile Power Wiring. • Fuse BOTH positive & negative leads close to the power connection. • Connect negative lead to negative (-) battery terminal or to battery ground connection. • Use grommets or sleeves to protect wires where they pass through firewall. • Do NOT assume that all metal body parts are grounded.

Power Supplies and Batteries Mobile Power Wiring. • Mobile installations are susceptible to interference

Power Supplies and Batteries Mobile Power Wiring. • Mobile installations are susceptible to interference from noise sources not present in home stations. • Ignition noise. • Present on received signal. • Reduced or eliminated by turning on the noise blanker. • Alternator whine. • High-pitched whine that varies in frequency with engine speed. • Present on either received or transmitted signal or both. • Eliminated by adding a filter to the DC wiring at the radio.

T 4 A 10 -- What is the source of a high-pitched whine that

T 4 A 10 -- What is the source of a high-pitched whine that varies with engine speed in a mobile transceiver’s receive audio? A. B. C. D. The ignition system The alternator The electric fuel pump Anti-lock braking system controllers

T 4 A 11 -- Where should the negative return connection of a mobile

T 4 A 11 -- Where should the negative return connection of a mobile transceiver's power cable be connected? A. B. C. D. At the battery or engine block ground strap At the antenna mount To any metal part of the vehicle Through the transceiver’s mounting bracket

Power Supplies and Batteries. • One or more battery cells connected in series. •

Power Supplies and Batteries. • One or more battery cells connected in series. • Battery cells create electrical energy through a chemical reaction. • Primary cell. • Chemical reaction is not reversible. • Cannot be recharged. • Secondary cell. • Chemical reaction is reversible. • Can be recharged.

Power Supplies and Batteries. • Capacity rated in Ampere-hours (AH) or milliampere hours (m.

Power Supplies and Batteries. • Capacity rated in Ampere-hours (AH) or milliampere hours (m. AH). • A 500 m. AH battery will provide: • • • 500 m. A for 1 hour. 50 m. A for 10 hours. 25 m. A for 20 hours. 5 m. A for 100 hours. etc.

Power Supplies and Batteries. • Individual cell voltage depends on materials used to construct

Power Supplies and Batteries. • Individual cell voltage depends on materials used to construct the cell. Chemistry Cell Voltage Type Lead-Acid 2. 1 V Rechargeable Carbon-Zinc (obsolete) 1. 5 V Disposable Alkaline 1. 5 V Disposable* Nickel-Cadmium (Ni. Cad) 1. 2 V Rechargeable Nickel-Metal-Hydride (Ni. MH) 1. 2 V Rechargeable Lithium Ion (LI-Ion) 3. 6 V Rechargeable

Power Supplies and Batteries. • Lead-Acid. • • • Secondary cell. Approximately 2. 12

Power Supplies and Batteries. • Lead-Acid. • • • Secondary cell. Approximately 2. 12 Volts per cell. “ 12 V” battery = 6 cells in series. • • • Open-Circuit at full charge: 12. 6 V to 12. 8 V Open-circuit at full discharge: 11. 8 V to 12. 0 V Loaded at full discharge: 10. 5 V Float Charge: 13. 8 V Daily Charge: 14. 2 V to 14. 5 V

Power Supplies and Batteries. • Lead-Acid. • If overcharged will release hydrogen gas. •

Power Supplies and Batteries. • Lead-Acid. • If overcharged will release hydrogen gas. • Remember the Hindenberg! • ALWAYS use in a well-ventilated area! • Gassing threshold ~14. 4 V.

Power Supplies and Batteries. • Sealed lead-acid (SLA). • • a. k. a. –

Power Supplies and Batteries. • Sealed lead-acid (SLA). • • a. k. a. – Gel-Cell. Electrolyte is in a gel form rather then liquid. Sealed so does not vent hydrogen gas. Avoid over charging to prevent build up of internal pressure.

Power Supplies and Batteries. • Battery Charging. • • Some batteries can be recharged,

Power Supplies and Batteries. • Battery Charging. • • Some batteries can be recharged, some cannot. Use the proper charger for the battery being charged. Batteries will wear out over time. Best if batteries are maintained fully charged. • Over-charging will cause heating and could damage the battery.

Power Supplies and Batteries. • Batteries for Handheld Radios. • Handhelds use battery packs

Power Supplies and Batteries. • Batteries for Handheld Radios. • Handhelds use battery packs • Packages of several individual batteries connected together. • Most are rechargeable. • Ni. Cd (nickel-cadmium). • Ni. MH (nickel-metal hydride). • Li-ion (lithium-ion). • For emergencies, have a battery pack that can use disposable batteries (usually AA size).

T 6 A 10 -- Which of the following battery types is rechargeable? A.

T 6 A 10 -- Which of the following battery types is rechargeable? A. B. C. D. Nickel-metal hydride Lithium-ion Lead-acid gel-cell All of these choices are correct

T 6 A 11 -- Which of the following battery types is not rechargeable?

T 6 A 11 -- Which of the following battery types is not rechargeable? A. B. C. D. Nickel-cadmium Carbon-zinc Lead-acid Lithium-ion

T 0 A 10 -- What can happen if a lead-acid storage battery is

T 0 A 10 -- What can happen if a lead-acid storage battery is charged or discharged too quickly? A. The battery could overheat, give off flammable gas, or explode B. The voltage can become reversed C. The memory effect will reduce the capacity of the battery D. All of these choices are correct

Questions?

Questions?

Technician Class Next Week Chapter 6 Communicating with Other Hams

Technician Class Next Week Chapter 6 Communicating with Other Hams