SPECIFICATIONS SDIBS 212 SDIBS 212 T Image Sensor

SPECIFICATIONS SDI-BS 212 | SDI-BS 212 T Image Sensor 1/3” 2. 1 Megapixel CMOS Scanning System Progressive Scan Total Pixels 2010(H) x 1108(V) Effective Pixels 1944(H) x 1092(V) S/N Ratio More than 50 d. B 1080 P (1920 x 1080) 25 P/30 P HD-SDI / 1. 0 Vp-p (75Ω, Composite) NTSC/PAL (W/O WDR) Color : 0. 5 Lux (B/W : 0. 1 Lux / Sens-up x 8 : 0. 02 Lux) Video Output Mode Video Output Level Min. Illumination Electronic Shutter Speed AUTO / FLK NTSC : 1/30~1/60, 000 sec PAL : 1/25~1/50, 000 sec White Balance Backlight Compensation D-WDR BLC / HLC / WDR / OFF AGC 0 ~ 20 Day & Night AUTO / BW / COLOR / EXT (Selectable) MODEL SELECTION MODEL RS-485 TDN POWER PIXEL SDI-BS 212 O X DC 12 V 2. 1 M SDI-BS 212 T O O DC 12 V 2. 1 M HD-SDI COLOR CCTV USER’S MANUAL CAMERA MEMO AUTO / AUTOext / PRESET / MANUAL ON / OFF DNR OFF / LOW / MIDDLE / HIGH Sens-up ON / OFF (~x 8) Motion Detection ON / OFF Privacy Masking ON / OFF (16 Zone Selectable) DEFOG ON / OFF D-Effect MIRROR / D-ZOOM / FLIP OUTPUT MODE 720 P / 720 P CROP / 1080 P FRAME RATE 1080 P-25 FPS / 30 FPS , 720 P CROP-50 FPS / 60 FPS Language English (Selectable) OSD Built-in Protocol Pelco-D / Pelco-C Communication RS-485 (Baud Rate : 2400~57600) Lens C / CS Mount Lens Power Supply DC 12 V (± 10%) Power Consumption Max. 180 m. A Operating Temperature -10°C ~ +50°C Operating Humidity 0% ~ 90% Dimension 65. 8(W) x 60. 6(H) x 101. 5(D)mm Weight Approx. 300 g * In accordance with customers’ request and OSD controller’s option, the specifications can be fixed or changed without notice. SDI-BS 212 T FEATURES • • • • • 1/3” Panasonic 2. 1 M Pixel Progressive Scan Color CMOS Sensor 1944 x 1092@30 fps Video Out (BNC) with NTSC/PAL Selectable Dual Output – Megapixel HD CCTV (BNC) and SD CCTV (BNC) out Defog (Visibility Enhancement on the Low Contrast Scene) Digital Zoom (x 8) Sens-up (x 8) Flicker Suppression DNR (2 D & 3 D Noise Reduction) DPC (Dead Pixel Compensation) 2 Auto (AE/AWB) Control HLC/BLC Support (High Light / Back Light Compensation) C / CS Mount Lens Rear OSD Control Board RS-485 Support External Day&Night In put Support Option : Mechanical TDN (ICR) Option : Dual Voltage (DC 12 V & AC 24 V) / Free Voltage (AC 230 V)

PRECAUTIONS NAME OF EACH PART • Do not install the camera in extreme temperature conditions. - Only use the camera under conditions where temperatures are between -10°Cand +50°C. Be especially careful to provide ventilation when operating under high temperatures. UPPER DIMENSION 3. Camera holder screw hole. 1. Lens (Option) • Do not install or use the camera in an environment where the humidity is high. - It can cause the image quality to be poor. • Do not install the camera under unstable lighting conditions. - Severe lighting change or flicker can cause the camera to work improperly. • Never use the camera close to a gas or oil leak. - It can cause malfunctions to occur. 4. Auto iris lens connector 2. Flange-back adjusting ring • Do not disassemble the camera. - There are no user-serviceable parts inside it. 1. Auto iris lens (Option) : This is the lens used with the camera. • Do not touch the front lens of the camera. - It is one of the most important parts of the camera. Be careful not to be stained by fingerprint. • Never keep the camera face to strong light directly. - It can damage the image sensor. • Do not drop the camera or subject them to physical shocks. - It can cause malfunctions to occur. • Do not expose the camera to rain or spill beverage on it. - If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode the electronic components. 2. Flange-back adjusting ring : A screw is provided to fix the lens mount. 3. Camera holder screw hole : Mounting base for installing the camera. 4. Auto iris lens connector : This connected supplies DC control. Signals needed to control the auto iris lens. REAR 1. HD-SDI Video out terminal 2. Video out terminal 3. OSD controller 4. Power LED • Do not expose the camera to radioactivity. - If exposed to radioactivity the image sensor will fail. 6. Power port * NOTE * • If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur. • Please check that the power satisfies the normal specification before connecting the camera. COMPOSITION Camera (W/O Lens) Camera holder C-Mount ring L- Wrench Screw Manual 5. I/O port 1. HD-SDI Video out terminal : BNC terminal for HD-SDI video signal output. 2. Video out terminal : Sends video signal and connects to the video input terminal of the monitor. 3. OSD Controller • SET UP : Used for the menu display. This button can be used to confirm settings. After changing the value of the selected function or current conditions. • UP & DOWN : Used for selecting items by moving the cursor up or down on the menu screen. • LEFT & RIGHT : Used when changing item values, by moving the cursor to left or right on the menu screen. 4. Power LED : Illuminates when power is supplied. 5. I/O Port • RS-485 Control port : You can control SETUP MENU through this port by using external controllers like a remote controller that RS-485 communication is supported. • MD Output port : Motion detection signals are output through this port. • GND : Ground