Poly Phenylene Oxide PPO In 1965 A Hay

Poly Phenylene Oxide (PPO) ø In 1965, A. Hay of General Electric produced polyphenylene oxide by the copper catalyzed oxidation of 2, 6 xylenol [(CH 3)2 C 6 H 3 OH)]. ø This is an aromatic polyester in which benzene rings is linked at the 1 and 4 position via. Oxygen atom. Repeat unit of PPO CORPORATE TRAINING AND PLANNING

Monomer Ingredients for PPO øThis polymer is made from 2, 6 dimethyl phenol CORPORATE TRAINING AND PLANNING

Chemistry of Preparation of PPO øPoly-(phenylene oxide) is known as poly (2, 6 -dimethylp-phenylene ether). ø The most successful method of preparation involves oxidative coupling of 2, 6 dimethyl phenol. ø The reaction is carried out at 28 -46°C by bubbling oxygen through a solution of the phenol in the presence of a copper (I) salt-amine complex for about 7 minutes. ø The reaction mixture is added to methanol filtered and washed with methanol to give a colourless polymer. CORPORATE TRAINING AND PLANNING

Chemistry of Preparation of PPO CORPORATE TRAINING AND PLANNING

Relations of Structure and Properties of PPO ø The rigid structure of the polymer molecules leads to a material of a high Tg of 208°C. ø There is a also a secondary transition at 116°C and the small molecular motions that this facilitates at room temperature give the polymer in the mass a reasonable degree of toughness. øWhen polymerized the polymer is crystalline but has a surprisingly low reported melting point (Tm) 257°C. øThe ratio of Tg & Tm of 0. 91 (in terms of K) is uniquely high. Because of the small differences in Tg and Tm there is little time for crystallization to occur on cooling from the melt and processed polymer is usually amorphous. ø However if molecular movements are facilitated by raising the temperature or by the presence of solvent crystallization can occur. CORPORATE TRAINING AND PLANNING

Relations of Structure and Properties of PPO ø The polymer is dissolved by halogenated and aromatic hydrocarbons of similar solubility parameter. Stress cracking can occur with some liquids. ø Being only lightly polar and well below the Tg at common ambient temperature the polymer is an excellent electrical insulator even at high frequencies. ø The polymer exhibit very good hydrolytic stability. ø One particular feature of PPO is its exceptional dimensional stability amongst the so-called engineering plastics. ø It has a low co-efficient of thermal expansion, low molding shrinkage and low water absorption thus enabling molding to close tolerances. ø It is more or less self-extinguishing polymer with a good chemical resistance properties. . CORPORATE TRAINING AND PLANNING

Characteristics of PPO (For Identification) øIt is semi-crystalline and having melting point of 257°C ø Characterized by good dimensional stability and excellent resistance to hydrolysis and very good dielectric properties over a wide range of temperature øIts short term and long term service temperatures are 100 and 80°C ø It is characterized by orange yellow flame with black smoke and self extinguishing character øIt melts but chars øIt smells phenolic (ink smell) while it is burnt. CORPORATE TRAINING AND PLANNING

Characteristics of PPO ø ø ø ø Possesses high melting point and glass transition temperature Low co-efficient of thermal expansion Continuos use temperature upto 100°C Excellent electrical properties Low loss factor Dissipation factor is quite low Very good dimensional stability High heat distortion temperature (179°C) Low moulding shrinkage Low warpage Good impact resistance Low water absorption Soluble only in halogenated and aromatic hydrocarbons Excellent flame retardancy Outstanding hydrolytic stability CORPORATE TRAINING AND PLANNING

Properties of PPO Properties Specific gravity 1. 10 Tensile strength Tensile modulus Flexural modulus 276 Elongation at break Impact strength Hardness Deflection temperature under load (1. 82 Mpa) Vicat softening point Coefficient of linear expansion Water absorption, 24 hrs Dielectric strength Dielectric constant Power factor Glass transition temperature Units Values ---- 1. 5 – MPa Mpa % izod, Notched, 0 C °C mm/mm/0 C % KV/mm 10 -6 Hz °C CORPORATE TRAINING AND PLANNING 41 -110 234 -276 2212 -3 J/m 107 -537 R 115 -120 82 -149 250 -310 6 -14 x 10 -5 0. 06 -0. 12 15. 7 -27 -6 2. 7 -2. 9 0. 0001 -0. 0025 100 -150

Properties of PPO Electrical Properties The electrical and dielectric properties of noryl are very good and almost independent of frequency and temperature. Chemical Properties ø PPO. mod. is resistance to dilute acids strong alkalines, solutions, alcohols, detergents, fats and oils depending on the additives. ø It is not resistant to concentrated acids, ketones, chlorinated hydrocarbons, aromatics they swell in many aliphatics. ø PPO mod. Is susceptible to stress cracking because of the styrene content. CORPORATE TRAINING AND PLANNING

Properties of PPO Weathering Resistance øWeathering resistance of PPO mod. is less than that of the unmodified material but still relatively high. øThe long-term heat resistance in air and water in the presence of oxygen is inferior to that of polyacetals. Flammability Flame retardant grades are self-extinguishing and nondripping. CORPORATE TRAINING AND PLANNING

Properties of PPO Toxicity øCorrespondingly marked grades are non-toxic Grades incorporating demolding aids, UV stabilizer and glass fiber reinforcements are permitted. øRestrictions apply only to colored grades (cadmium pigments). øSuitable non-toxic pigments are carbon black, Ti 02, ultramarine blue and iron oxide. that of polyacetals Flammability Flame retardant grades are self-extinguishing and nondripping. CORPORATE TRAINING AND PLANNING

Additives of PPO 1. Flame retardants 2. Glass fibers CORPORATE TRAINING AND PLANNING

Grades of PPO They are available in the following grades. ø Glass reinforced ø Foam grade ø Plating grade ø High modulus grade ø Blow moulding grade ø Injection moulding grade CORPORATE TRAINING AND PLANNING

Processing considerations of PPO 280 -300°C cylinder Typical temperatures about øandare mold temperatures 100 – 120°C. ø finish and streakiness. Because of this it is advisable to purge machines before they are cooled down after molding. The ø almost independent of shear rate. CORPORATE TRAINING AND PLANNING

Processing considerations of PPO ø Due to their extremely low moisture absorption PPO resin can be molded without the need of drying. e in. Surface defect ø avoided by proper drying. øDrying temperature grades. resin Temperature the with vary of 110°C for 2 hours are recommended for drying. CORPORATE TRAINING AND PLANNING

Processing considerations of PPO They can be processed by the following processing techniques. ø Extrusion ø Foam moulding ø Thermoforming CORPORATE TRAINING AND PLANNING

Surface Finishing of PPO ø CORPORATE TRAINING AND PLANNING

Machineability of PPO Joining øWelding Surface temperature of 260 to 2900 C are selected for heated tool welding. Friction welding takes place at speeds of 1200 rpm and contact pressure of 20 N mm-2. Ultrasonic and resistance wire welding are also used. øBonding PPO can be bonded using solvents such as dichloroethylene, toluene, chloroform or 950, dichloroethylene with 5% carbontetrachloride. High tensile and shear strength are achieved with rubber, epoxide, resin, silicon, cyanoacrylate and PU adhesives. CORPORATE TRAINING AND PLANNING

Applications of PPO øAutomotive øElectricals/Electronics øMiscellaneous CORPORATE TRAINING AND PLANNING

Applications of PPO Automotive: Instrument panels, steering column, cladding, central consoles, loud speaker housings ventilator grills, nozzles, parcel shelves, radiator tanks, cable connectors, bulb sockets, air inlet and outlet grills and outer mirror housings. CORPORATE TRAINING AND PLANNING

Applications of PPO Electricals/Electronics: Television tuner strips, microwave insulation component, transformer housings. Computer terminals, printers, modems, typewriter bases, video games, copier, capacitor casings, outlet boxes, coil bobbins, smoke detectors, intrusion alarm, motor covers and switches. Capacitor casing CORPORATE TRAINING AND PLANNING

Applications of PPO Miscellaneous: Water pumps, water meters, sprinkler systems, hot water tank, washing machine parts, welder’s protective visors, tennis racquets, textile components and valves for drink vending machines. Welder’s protective visor Washing machine parts CORPORATE TRAINING AND PLANNING

Applications of PPO Kettle CORPORATE TRAINING AND PLANNING

e Blends of PPO ø Polyphenylene oxide is completely miscible with polystyrene in all proportions. The glass transition temperature of these blends change smoothly with composition. ø injection or blow moulding, extrusion calendering, thermoforming and reinforced with 0 -30 weight percentage glass fiber. ø They have good processability, toughness, flame retardance, dimensional stability, resistance to hot water, economy, HDT (95 -150°C), low density and moisture absorption. CORPORATE TRAINING AND PLANNING

Blends of PPO / Nylons ø These are blends (compatibilized) with 40 -60 weight percentage of nylon. ø PPO provide excellent heat resistance, toughness and nylon (crystalline) resists oils, gasoline and solvent, PPO / Nylons alloys have a lower density, higher toughness and show less tool/machine wearcompared to machine filled Nylon. ø Polyamide grades are used for automotive body panels which require paint oven temperature upto 175°C. ø CORPORATE TRAINING AND PLANNING

List of Manufacturers/Suppliers of PPO CORPORATE TRAINING AND PLANNING