Launch Umbilical Tower PRINT ON CARDSTOCK ScoreMountain Fold

Launch Umbilical Tower PRINT ON CARDSTOCK Score/Mountain Fold line Score/Mountain Fold glue tabs & lower tower cap. Score/Mountain Fold glue tabs & upper tower cap. Score/Mountain Fold line Glue Tab © 2005 Drawn by Michael Burke This cardmodel is only for personal and not commercial use.

As the Crane is designed to rotate, the builder may wish to build it from cardstock for extra strength. You need build only one crane – these are alternate parts Denote Mountain Fold/Score Lines Glue Tab Machinery House Lightning Rod Roll into tube Glue Tab Score and Mountain Fold along dark gray line at base of tower Mountain Fold/Score lines Mountain fold all triangular glue tabs on both ends COLBY CRANE SEATTLE Front © 2005 Drawn by Michael Burke This cardmodel is only for personal and not commercial use. Tower Base Rear Score/Mountain Fold line COLBY CRANE SEATTLE Crane Keel Sandwich and glue both halves around cardstock Glue Tabs Glue Tab Top Bottom Inner Sleeve Centering Circle Print on Cardstock Glue Tab Score/Mountain Fold Lines Glue Tab Score and Mountain Fold along dark gray line at base of tower 10 TON 25 TON Trim this piece to fit Score/Mountain Fold Lines 25 TON 10 TON Glue Tab Score and Mountain Fold along dark gray line at base of tower

PRINT ON CARDSTOCK SIDE 3 1 1 SIDE 2 SIDE 4 Circles on underside of platform are for locating holes for tower pedestals. After platform is complete, carefully drill holes with tip of X-Acto knife. Insert pedestal tubes all the way to the underside of the top of the platform deck. Hold Down Arms Carefully Cut out White Portion 1 1 SIDE 2 Mountain Fold/Score Lines SIDE 4 Carefully Cut out White Portion Hold Down Arm Supports Hold-Down Arm Supports These are wedge-shaped pieces that are glued to the underside of the square protrusions in the top opening of the thrust chamber and to the face of the thrust chamber liner. All folds are Mountain folds. 1 1 SIDE 1 Glue Tabs Valley Fold/Score Lines See Crane Parts Page for Hold Down Arms and Launcher Pedestals Thrust Chamber Liner Center in holes cut of launcher platform, between upper and lower decks. © 2005 Drawn by Michael Burke This cardmodel is only for personal and not commercial use.

SM Arm Service Arms S-IVB Arms Glue Tab Forward Arm Glue Tab S-I & SII Arms Aft Arm Glue Tab S-II Forward Glue Tab Solid red sections are the walkway (bottom) of the arm – gray section with diagonal cross members are the tops. Sides have diagonal cross members with “mesh” on bottom half. Score/Fold lines S-II Intermediate Arm Glue Tab Both ends are “capped” for rigidity and for mounting to the tower. All folds are “mountain” folds. PRINT TO BOND PAPER Recommend printing on bond paper. CM Access Arm Score/Fold Lines Glue Tab Carefully cut this white notch out Score/Fold line Glue Tab Score/Fold Lines Score/Fold lines Damper Arm Glue Tab Other arms are mounted to front of tower, like this. (See drawing for placement. ) Glue Tab Carefully cut this white section out When CM Access Arm is complete, from the top, it should be shaped like and mounted to side of tower, like this. S-II Aft Glue Tab Score/Fold lines Glue Tab S-IC Forward S-IC Intertank Glue Tab When completed, the Damper arm assembly goes together like this. Score/Fold lines © 2005 Drawn by Michael Burke This cardmodel is only for personal and not commercial use.

PRINT TO BOND BAPER Launcher Base Pedestals Roll into double layered tubes – Glue edge to centerline Lightning Rod Roll into double layered tube – Glue edge to centerline. Cut out small circle on top of tower, glue tube in line with hole in order to stabilize crane and allow it to rotate. As the Crane is designed to rotate, the builder may wish to build it from cardstock for extra strength. You need build only one crane – either these parts or those on the Tower Base page Inner Sleeve – on bottom of crane Roll into double layered tube – Glue edge to centerline Glue tube to bottom of Crane Keel, centered in small circle. Inner Sleeve should fit snugly enough inside Outer Sleeve that Crane doesn’t wobble, but loosely enough to allow rotation. Inner Sleeve Hold Down Arms Tower Outer Sleeve Top Lightning Rod Crane Keel Roll into tube Sandwich and glue both halves around cardstock Bottom Inner Sleeve Centering Circle Glue to square protrusions in thrust chamber opening on top of launcher platform. Cut out bottom bulkhead of Saturn V, glue to cardstock, and use to align Hold Down Arms such that they are centered and support the rocket model. All lines are Score/Mountain Fold Lines Machinery House Mountain Fold/Score lines Glue Tab Crane Boom Score/Mountain Fold Lines 10 TON 25 TON Trim this piece to fit Score/Mountain Fold Lines Mountain fold all triangular glue tabs on both ends COLBY CRANE SEATTLE Outer Sleeve – Inside top of Tower Front Rear 25 TON 10 TON COLBY CRANE SEATTLE Glue Tab © 2005 Drawn by Michael Burke This cardmodel is only for personal and not commercial use. Glue Tab Score/Mountain Fold line

S-IVB Service Module This wedge is a glue tab Command Module Engine Fairings S-IVB Centering Rings Glue Rings to Cardstock and glue one in front Launch Escape Tower and one in back Roll Into Cylinder of S-IVB Roll Into double-layered tubes S-IC, Interstage, & S-II U N I T E D S T A T E S PRINT TO BOND BAPER Interstage © 2005 Drawn by Michael Burke This cardmodel is only for personal and not commercial use. Centering Rings Glue one in front and back of S -1 C/S-II Tube Glue to Cardstock Saturn V Rear Bulkhead Glue to cardstock and use to align and center Hold Down Arms on Launcher Base. U S A SM/LM Adapter F-1 Engines Fins – Trim off Root Tabs

Damper Arm