GEARS Gears and shafts are basically wheel and

GEARS Gears and shafts are basically wheel and axles, but gears have cogs, or teeth on their circumference.

GEARS Gears turn either clockwise or counterclockwise. When gears touch, we call it meshing. As gears mesh, they turn in opposite directions.

GEARS In multiple gear sets, all odd numbered gears turn the same direction, and the even numbered gears turn in the opposite direction.

GEARS C A B To make two gears turn in the same direction, (A & C) another gear (B) needs to be between the two. This gear, without a load, is called the idler. It can be any size, or there can be multiple idler gears.

GEARS Gears are generally used for one of four different reasons: 1. To reverse the direction of a rotational force. 2. To increase or decrease the speed of rotation. 3. To move rotational motion to a different axis. 4. To keep the rotation of two axis synchronized.

GEARS Another option exist with a rack and pinion gear set. Rack and pinions convert rotary motion to linear motion.

GEARS Bevel gears can change the direction of the rotational axis.

GEARS Worm gears are like screws. They prevent slippage, and reduce rotational speed and increase torque.

GEARS Planetary gears utilize a system that consists of one or more outer gears, or planet gears, revolving about a central, or sun gear. Typically, planet gears are mounted on a movable arm or carrier which itself may rotate relative to the sun gear.

GEARS A common example of this type of gearing system is the manual pencil sharpener. In this instance, the planet gear is stationary and the sun gear moves.

GEARS Another way to make two gears turn the same direction is to use a chain. The gears are shaped a little different, and are called sprockets. Advantages include greater distance between gears, a greater tolerance for alignment, and less damage to the system should a chain break.

GEARS Conservation of energy requires that the amount of power delivered by the output gear or shaft will never exceed the power applied to the input gear, regardless of the gear ratio.

GEARS Actual output will never reach theoretical outputs due to friction, errors, entropy, or any number of other external forces or situations involved.

GEARS Gear = # of Teeth on Driven Gear Ratio # of Teeth on Driving Gear 60 35 example: 35 = 7 60 12 The 60 teeth gear will spin 7 times, while the 35 teeth gear will spin 12 times.

GEARS Compound Gears are gears consisting of two gears turning on the same axle. The have the same rate of rotation.

GEARS Gear ratios for each individual gear pair are multiplied together to compute the overall compound gear ratio.

GEARS Example: Gear ratio between A and B is 12: 36 or 1: 3. The gear ratio between C and D is 12: 60 or 1: 5 Overall gear ratio is 1/3 x 1/5 = 1: 15. A will spin once for D to spin 15 times.

GEARS Torque is rotational force. Torque is often talked about in using it to drive in screws, fasten nuts onto bolts and other such activities.

GEARS Torque = Force x Lever Arm (distance between force and the objects center of mass) [In our case, the radius of the wheel]. Formula: t = f x L

GEARS Torque is measured in the relationship between the measurements used in determining force and length, i. e. torque is measured in footpounds if the force is lbs. and the distance feet; or Newton – meters if Newton and meter are used; inch-ounces if these two force and distance measurements are used.

GEARS The relationship between torque, gear ratio, speed, etc. increases or decreases on a linear scale. This could be either a direct relationship (as gear ration increases from 1: 3 to 1: 5 speed increases) or an indirect or inverse relationship, (torque decreases as speed increases. ) As a consequence, more torque = less speed and vise-versa.

GEARS When gears mesh, both gears exert the same amount of force in opposite directions at any given point.

GEARS If a driving gear of 60 teeth is meshed with a driven gear of 36 teeth, then the force where the two gears meet is equal to f 36 = f 60. Torque ratio is therefore equal to the gear ratio.

GEARS Safety must be a consideration when working with gears. Extreme pressure can cause gears to shatter or strip out teeth. Pinching hazards exist as well.