Fiber Optic Installation and User Manual ver 1

Fiber Optic Installation and User Manual ver. 1. 0 [to integrate with the user manual of DAS M 32/M 44] PORSCHE PCM 3. 0 – PCM 3. 1 www. dasdvbt. com Multiconn Srl

Installation PCM 3. 0 - PCM 3. 1: 1. To install the DAS® receiver, refer to the specific user manual; Warning on the connection of the power supply cable : - RED wire (fig. 3) must be DISCONNECTED. The switch (ON/OFF) of the receiver will be controlled by the Fiber-Optic activity - YELLOW wire (fig. 1) must be connected to the +12 V permanent/battery (fig. 1) - BLACK wire (fig. 2) must be connected to the GND. (fig. 2) 3 1 Power supply cable 2 2. Disconnect the original Fiber Optical cable (fig. 4) from the Head Unit and match it directly to DAS® fiber (fig. 4) optic female connector of the harness on equipment (fig. 5) 4 4 5 PCM 3. 0 – PCM 3. 1 2 Multiconn Srl

3. Match the two other connectors of DAS® harness (fig. 6) respectively inside the original accessory (fig. 7) (fig. 6) (fig. 7) ® and the other one inside DAS receiver (fig. 8) 7 7 8 8 6 5 4. Connect one of the 3 DAS® Video-OUT (fig. 8) trough the adapter cables on equipment (fig. 9) and the (fig. 8) needed accessory with white Fakra connector (DCABMQS-RCA in fig. 9. 1) with the Video-IN on the Head needed accessory (DCABMQS-RCA in fig. 9. 1) Unit (fig. 10) 9 9. 1 9 8 PCM 3. 0 – PCM 3. 1 3 Multiconn Srl

The PCM 3. 0 - PCM 3. 1 Head Unit module (fig. 10) 10 Video. IN White cover Black 12 P Insert the 2 female crimped pins of DAS cable (fig. 9. 1 DCABMQS-RCA) inside the black 12 P housing and then in white Fakra cover. In case these connectors are already available in the unit, just connect the pins in the pin-out position recommended below. Insert the wire with label + in pin 27 (positive signal). pin 27 If the pin 27 is already used by rear camera, connect to pin 26 Insert the wire with label - inside the pin 24 (negative pin 24 signal). If the pin 24 is already used by rear camera connect pin PCM 3. 0 – PCM 3. 1 25 4 9. 1 Multiconn Srl

User Manual PCM 3. 0: To enter in DAS WARNING: For the basic settings such as color, contrast, brightness and format, please WARNING: DAS TV tuner: refer to the menu of the car and make sure that the format is congruent with the set 1) press SOURCE then select TV icon on touch screen monitor and touch the screen to view SOURCE TV menu on the DAS. images. 2) Or press and hold TUNER button, until the TV icon will appear on touch screen monitor TUNER TV Next Channel (RIGHT arrow on remote control) Previous Channel (LEFT arrow on remote control) PCM 3. 0 5 Multiconn Srl

User Manual PCM 3. 1: To enter in DAS WARNING: For the basic settings such as color, contrast, brightness and format, please WARNING: DAS TV tuner: refer to the menu of the car and make sure that the format is congruent with the set 1) press SOURCE then select TV icon on touch screen monitor and touch the screen to view SOURCE TV menu on the DAS. images. 2) Or press and hold TUNER button, until the TV icon will appear on touch screen monitor TUNER TV Previous Channel (LEFT arrow on remote control) PCM 3. 1 6 Next Channel (RIGHT arrow on remote control) Multiconn Srl

Remote Control Functions: UP ARROW MENU NAVIGATION - ZAPPING KEY ON-OFF TURNING ON/OFF LEFT ARROW MENU NAVIGATION - ZAPPING KEY TV/AV 1/AV 2 SELECTION CONFIGURATION MENU/OK FUNCTIONS SET UP RIGHT ARROW MENU NAVIGATION - ZAPPING KEY DAS MENU TV/RADIO SELECTION AND SEARCH SYSTEM NUMBER KEYPAD FOR CHANNEL PRE-SELECTION DOWN ARROW MENU NAVIGATION - ZAPPING KEY VOLUME ADJUSTMENT PCM 3. 0 – PCM 3. 1 7 Multiconn Srl

MULTICONN Srl Via Selvetta, 7 - 21100 Varese – Italy Tel. +39 0332 280512 Fax +39 0332 283048 www. dasdvbt. com