Electrical Machines Induction MotorsNote1 1 Induction Motor Comparing

Electrical Machines Induction Motors_Note(1) 1

Induction Motor • Comparing with synchronous motor No dc field current is required to run the machine. • Instead, amortisseur windings are installed in the rotor. • The machine is called “Induction” because the rotor voltage is induced in the rotor windings rather than physically connected by wires. • It is possible to use an induction machine as motor or generator, but there are many disadvantages to use it as generator. 2

Induction Motor Components 1) Stator: Consisting of a steel frame that supports a hollow, cylindrical core of stacked laminations. Slots on the internal circumference of the stator house the stator winding 2) Rotor: There are two different types of induction motor rotor: Squirrel cage rotor (Cage rotor): Consists of series of conducting bars laid into slots carved in the face of rotor and shorted at either end by large shorting rings. 3

Wound rotor IM • A wound rotor has a 3 -phase winding, similar to the stator winding. • The rotor winding terminals are connected to three slip rings which turn with the rotor. The slip rings/brushes allow external resistors to be connected in series with the winding. • The external resistors are mainly used during start-up under normal running conditions the windings short circuited externally. 4

5

Induction Motors Operation Principle 1) The three-phase stator is supplied by balanced three-phase voltage that drives an AC magnetizing current through each phase winding. 2) The magnetizing current in each phase generates a pulsating AC flux. 3) The total flux in the machine is the sum of the three fluxes. 4) The summation of the three AC fluxes results in a rotating flux, which turns with constant speed and has constant amplitude. 6

5. The rotating flux induces a voltage in the short-circuited bars of the rotor. This voltage drives current through the bars. 6. The induced voltage is proportional with the difference of motor and synchronous speed. Consequently the motor speed is less than the synchronous speed 7. The interaction of the rotating flux and the rotor current generates a force that drives the motor. 7

IM Rotating Field Consider a simple stator with 6 salient poles - windings AN, BN, CN. The windings are mechanically spaced at 120° from each other and connected to a 3 -phase source. AC currents Ia, Ib and Ic will flow in the windings, but will be displaced in time by 120°. Each winding produces its own MMF, which creates a flux across the hollow interior of the stator. The 3 fluxes combine to produce a magnetic field that rotates at the same frequency as the supply. 8

Rotating Field - Direction of rotation The phase current waveforms follow each other in the sequence A-B-C. This produces a clockwise rotating magnetic field. If we interchange any two of the lines connected to the stator, the new phase sequence will be AC-B. This will produce a counterclockwise rotating field, reversing the motor direction. 9

Number of Poles – Synchronous Speed 1) The rotating speed of the revolving stator flux can be reduced by increasing the number of poles (in multiples of two). In a fourpole stator, the phase groups span an angle of 90°. In a sixpole stator, the phase groups span an angle of 60°. 2) This leads to the definition of synchronous speed (rotating stator flux speed): Ns = 120 f/p where Ns = synchronous speed (rpm), f = frequency of the supply (Hz), p = number of poles 10

Induction Motors Slip The difference between the synchronous speed and rotor speed can be expressed as a percentage of synchronous speed, known as the slip: X 100 % where s = slip, Ns = synchronous speed (rpm), N = rotor speed (rpm) At no-load, the slip is nearly zero (<0. 1%). At full load, the slip for large motors rarely exceeds 0. 5%. For small motors at full load, it rarely exceeds 5%. The slip is 100% for locked rotor. 11

Frequency Induced In the Rotor The frequency induced in the rotor depends on the slip: where f. R = frequency of voltage and current in the rotor, f = frequency of the supply and stator field, s = slip 12

Examples • Example 7 -1 13

Equivalent circuit of induction motor • Transformer Model of an Induction Motor • Per-phase equivalent circuit of transformer:

Induction Motors Equivalent circuit An induction motor can be described as rotating transformer, it is input is three phase voltage and current, the output of IM is shorted out so no electrical output exist, instead the output is mechanical. The Per phase equivalent circuit of an induction motor: Stator: Resistance and self inductance , magnetization reactance X M and core resistance RC Rotor: resistance and reactance 15

Transformer model of induction motor Magnetization curve of induction motor

Transformer Model of Induction Motor • Note: slope of induction motor’s magneto-motive force-flux curve is much shallower than curve of a good transformer • because there is an air gap in an induction motor which greatly increase reluctance of flux path & therefore reduces coupling between primary & secondary windings • Higher reluctance caused by air gap means a higher magnetizing reactance XM in equivalent circuit will have a much smaller value (larger susceptance BM) than its value in an ordinary transformer.

Power flow diagram 18

Power and torque in Induction Motors • The supply power is: • The power transferred through the air gap by the magnetic coupling is the input power (Pin) minus the stator copper loss and the magnetizing (stator iron) loss. 19

• The stator copper and core losses are determined using the following: • The electrically developed power (Pdv) is the difference between the air gap power (Pag) and rotor copper loss. 20

Induction Motors Output Power • The subtraction of the mechanical ventilation and friction losses (Pmloss) from the developed power gives the mechanical output power (in Hp): 21

Induction Motors Efficiency and Torque • The motor efficiency: • Motor torque: 22

23

Example(1) A 460 V, 60 Hz, 25 hp, 4 pole, Y connected induction motor has following impedances in Ω /phase referred to stator circuit: R 1 = 0. 641 Ω R 2=0. 332 Ω X 1 = 1. 106 Ω X 2 = 0. 464 Ω XM=26. 3 Ω The total rotational losses are 1100 W, & assumed to be constant core loss is lumped in with rotational losses. For rotor slip of 2. 2 % at rated voltage & rated frequency, find: (a) Speed (b) stator current (c) P. F. (d) Pconv & Pout (e) Tind & Tload (f) Efficiency 24

IM Torque-Speed Characteristic • How does the torque of IM change as the load changes? • At light loads: The rotor slip is very small and so the relative motion between the rotor and magnetic field is very small and the rotor frequency is also very small. Current and ER is very small and in phase so BR is relatively small, as the rotor magnetic field is very small then the induced torque is small: Rotor power factor 25

IM Torque-Speed Characteristic • At heavy loads: – As load increase, the slip increase, rotor speed falls down, – thus, more relative motion appears and produce stronger ER, – larger rotor current IR and so rotor magnetic field BR will be seen. – The angle of the rotor current will be also changed. – The increase in BR tend to increase in the torque. 26

• Starting torque: is 200 -250% of the full load torque (rated torque). • Pullout torque: Occurs at the point where for an incremental increase in load the increase in the rotor current is exactly balanced by the decrease in the rotor power factor. It is 200 -250 % of the full load torque. 27

A typical induction motor torquespeed characteristic curve 28

Torque-Speed Characteristic Curve Regions Low-slip region: In this region the motor slip increases approximately linearly with increase load & rotor mechanical speed decreases approximately linearly with load. • In this region rotor reactance is negligible, so rotor PF is approximately unity, while rotor current increases linearly with slip. • The entire normal steady-state operating range of an induction motor is included in this linear low-slip region.

• Moderate-slip region In moderate-slip region rotor frequency is higher than before, & rotor reactance is on the same order of magnitude as rotor resistance. - In this region rotor current, no longer increases as rapidly as before and the P. F. starts to drop - peak torque (pullout torque) of motor occurs at point where, for an incremental increase in load, increase in rotor current is exactly balanced by decrease in rotor P. F.

High-slip region: • In high- slip region, induced torque actually decreases with increased load, since the increase in rotor current is completely overshadowed by decrease in rotor P. F. • For a typical induction motor, pullout torque is 200 to 250 % of rated full-load torque • And starting torque (at zero speed) is about 150% of full-load torque • Unlike synchronous motor, induction motor can start with a full-load attached to its shaft

Comments on IM torque speed curve 1 - Induced torque of motor is zero at Syn. Speed. 2 - Torque-speed curve is nearly linear between no load and full load. In this range rotor resistance is much larger than its reactance so rotor current, rotor magnetic field & induced torque increase linearly with increasing slip 3 - There is a maximum possible torque that cannot be exceeded (pullout torque) is 2 to 3 times rated fullload torque of motor.

Comments on IM torque speed curve (con. ) 4 - Starting torque on motor is slightly larger than its full-load torque, so this motor will start carrying any load that it can supply at full power 5 - Note: that torque on motor for a given slip varies as square of applied voltage. This is useful in one form of induction motor speed control that will be described. 6 - If rotor of induction motor driven faster than sync. Speed, direction of Tind reverses & machine become Gen. converting Pmech to Pelec.

Induction Motor/Generator Mode

Induction Motor Maximum Torque Using Thevenin Equivalent • Thevenin equivalent voltage of induction motor:

ZTH=RTH+j. XTH = j. XM(R 1+j. X 1)/[R 1+j(X 1+XM)] • Since XM>>X 1 and XM+X 1>>R 1 , Thevenin resistance & reactance can be approximated as: RTH ≈ R 1 ( XM/ [X 1+XM] ) ^2 XTH ≈ X 1 •

Induction Motor Maximum Torque In IM the maximum power transfer occurs when: R 2/s=√RTH^2 + (XTH+X 2)^2 So maximum slip Smax is: Smax=R 2 / √RTH^2 + (XTH+X 2)^2 By applying this value of slip to torque equation in slide (8): Note: smax ~ R 2 , Maximum torque is independent of R 2

Effect of Varying Rotor Resistance in wound rotor IM Effect of varying rotor resistance on T-ω of wound rotor

Example (2) • A 2 pole, 50 Hz induction motor supplies 15 k. W to a load at a speed of 2950 r/min. Determine: - The motor’s slip? - The induced torque in the motor in Nm under these conditions? - The operating speed of the motor be if its torque is doubled? - The power will be supplied by the motor when the torque is doubled?

Solution: (a) nsync= 120 fe/p= 120 x 50/2=3000 r/min s= 3000 -2950/3000=0. 0167 or 1. 67% (b) Tind=Pconv/ωm=15 / (2950)(2πx 1/60)=48. 6 N. m. (c) In the low slip region, the torque-speed is linear & induced torque ~ s doubling Tind slip would be 3. 33 % nm=(1 -s)nsync =(1 -0. 0333)(3000)=2900 r/min (d) Pconv=Tind ωm=97. 2 x 2900 x 2πx 1/60=29. 5 k. W

Example (3) • A 460 V, 25 hp, 60 Hz, 4 -pole, Y-connected wound rotor induction motor has the following impedances in ohms per-phase referred to the stator circuit: • R 1 = 0. 641 Ω R 2 = 0. 332 Ω • X 1 = 1. 106 Ω X 2 = 0. 464 Ω Xm = 26. 3 Ω a)What is the max torque of this motor? At what speed and slip does it occur? b) What is the starting torque? c) When the rotor resistance is doubled, what is the speed at which the max torque now occurs? d) What is the new starting torque?

Solution : using Thevenin equivalent : = 266/ √(0. 641)^2+(1. 106+26. 3)^2= 255. 2 V =(0. 641)(26. 3/[1. 106+26. 3])^2=0. 59 Ω XTH≈X 1=1. 106 Ω (a) Smax = R 2 / √RTH^2 + (XTH+X 2)^2 =0. 332/√(0. 59)^2+(1. 106+0. 464)^2=0. 198

- This corresponds to a mechanical speed of : Nm=(1 -s)Nsync=(1 -0. 198)(1800)=1444 r/min - The maximum torque at this speed : = 3(255. 2)^2 / {2 x 188. 5 x[0. 59+√ 0. 59^2+(1. 106+0. 464)^2]} =229 N. m.

(b) Starting torque of motor found by s=1 = 3 x 255. 2^2 x 0. 332 / {188. 5 x[(0. 59+0. 332)^2+(1. 106+0. 464)^2]}=104 N. m. c) Rotor resistance is doubled, s at Tmax doubles smax=0. 396 , and the speed at Tmax is: nm=(1 -s)Nsync=(1 -0. 396)(1800)=1087 r/min Maximum torque is still: Tmax=229 N. m. and starting torque is : Tstart=3(255. 2)(0. 664) / {(188. 5)[(0. 59+0. 664)^2+(1. 106+0. 464)^2]} =170 N. m.