DOE Electrical Safety Handbook 2016 EFCOG Electrical Safety

DOE Electrical Safety Handbook 2016 EFCOG Electrical Safety Workshop

Working Group Members • • • Mike Hicks, DOE INL Lloyd Gordon, LANL Tim Snow, NREL Richard Green, LLNL Don Bourcier, LANL Eugene Santiago, BNL Joe Kilar, ANL John Lacenere, PPPL John Echave, LANL Marion Wilde, SNL Mark Mathews, ORNL Jerry Meisinger, HQ-DOE

History of Handbook • • • 1990 - 1993 Development 1993 - draft, Chapters 1 - 8 1994 - 1997, R&D Development January 1998 - release 2003 - attempt to eliminate March 2004 - 1 st R&D Electrical Safety Meeting/Workshop April 2004 - Edit to Handbook due December 2004 - Revised handbook, added excavation March 2005 - 2 nd R&D Electrical Safety Meeting/Workshop March 2006 - 3 rd R&D Electrical Safety Meeting/Workshop July 2007 - 1 st Joint DOE Electrical Safety Workshop

History of Handbook • • • October 2008 - revision finalized January 1, 2009 – was submitted to DOE Back to the drawing board 2010 - revised Electrical Safety Handbook, 2 new chapters Added equipment approval and hazard classification 2010 – 2013 editing, code referencing, reorganization, REVCOM • 2013 published, two new EFCOG chapter pushed to appendices, controversial

DOE Handbook - 2004 1. 0 Introduction 2. 0 General Requirements 3. 0 Electrical Preventive Maintenance 4. 0 Grounding 5. 0 Special Occupancies 6. 0 Requirements for Specific Equipment 7. 0 Work in Excess of 600 V 8. 0 Temporary Wiring 9. 0 Enclosed Electrical/Electronic Equipment 10. 0 Research and Development 11. 0 Electrical Safety During Excavations – EFCOG product 12. 0 References Appendix A - DOE Model Electrical Safety Program Appendix B - Acronyms and Definitions Appendix C - Work Matrices - Examples Appendix D - Regulation Matrices

DOE Electrical Safety Handbook - 2013 1) Introduction 2) General Requirements 3) Hazard Analysis 4) Electrical Preventive Maintenance 5) Grounding 6) Special Occupancies 7) Requirements for Specific Equipment 8) Work in Excess of 600 V 9) Temporary Wiring 10) Electrical Safety During Excavation 11) Enclosed Electrical/Electronic Equipment 12) Unlisted Electrical Equipment Approval 13) Research and Development A – DOE Model Electrical Safety Program B – Acronyms and Definitions C – Unlisted Electrical Equipment - EFCO D – Hazard Analysis - EFCOG E – Referenced Citations F – Severity Tool general see Appendix D code, explosives code R&D see Appendix C R&D code EFCOG

2016 Working Group Goal • Reorder Handbook to include all material in main body • To eliminate code repetition • To brainstorm new sections

Consideration for Elimination • The next few slides look at each chapter for – Elimination – Update – Closer consideration

1. 0 Introduction 1. 1 Purpose 1. 2 Scope 1. 3 Electrical Safety Program 1. 4 Authority Having Jurisdiction

2. 0 General Requirements 2. 1 Electrical Maintenance or Repairs 2. 2 Basic Safeguards 2. 3 Responsibilities 2. 4 Modifications to Facilities 2. 5 Approval of Electrical Equipment 2. 6 Codes, Standards, and Regulations 2. 7 Training and Qualifications of Qualified Workers 2. 8 Working Space Around Electrical Equipment 2. 9 Identification of Disconnecting Means 2. 10 Work Instructions 2. 11 Electrical Personal Protective Equipment 2. 12 Work Practices

3. 0 Hazard Analysis This Chapter, created by our EFCOG group was pushed to an Appendix

4. 0 Electrical Preventative Maintenance 4. 1 Development and Implementation Requirements 4. 2 Electrical Preventive Maintenance Program 4. 3 Maintenance 4. 4 Inspection 4. 5 Essential Elements 4. 6 Planning and Developing an EPM Program, and Fundamentals of EPM 4. 7 Ground-Fault Protection and Arc Fault Circuit Interrupters 4. 8 Overcurrent Protective Devices

5. 0 Grounding 5. 1 Specifications and Drawings 5. 2 Circuit and System Grounding 5. 3 Equipment Grounding 5. 4 Bonding 5. 5 Grounded or Ungrounded Systems 5. 6 Grounding Requirements 5. 7 Grounding Electrode Conductor 5. 8 Main Bonding Jumper 5. 9 System with Grounded Conductor 5. 10 Equipment Grounding Conductor 5. 11 Ungrounded Systems 5. 12 Grounding a Separately Derived System 5. 13 Grounding Electrode System 5. 14 Personnel Protective Grounds

6. 0 Special Occupancies 6. 1 Explosives 6. 2 Prevention of External Ignition and Explosion 6. 3 Hazardous Locations 6. 4 Electrical Equipment for Class I, II, and III Areas 6. 5 Descriptions, Features, and Test Criteria of Enclosures for Hazardous (Classified) Locations 6. 6 Underground Facilities

7. 0 Requirements for Specific Equipment 7. 1 Conveying Systems 7. 2 Cranes and Hoists 7. 3 Elevators and Escalators 7. 4 Portable and Vehicle-Mounted Generators 7. 5 Batteries

8. 0 Work in Excess of 600 Volts 8. 1 Responsibilities for Safety 8. 2 Training 8. 3 Job Briefings 8. 4 Personal Protective Equipment and Protective Clothing 8. 5 Protective Grounding of Lines and Equipment 8. 6 Installing or Removing Conductors 8. 7 Special Tools 8. 8 Tree Trimming 8. 9 Underground 8. 10 Ferro-Resonance

9. 0 Temporary Wiring 9. 1 Requirements and Installation Conditions of use 9. 2 Using Assured Equipment Grounding Conductor Program 9. 3 Portable Electrical Tools and Equipment

Chapter 10 Electrical Safety During Excavation 10. 1 General 10. 2 Utilities Identification 10. 3 Utilities Verification and Marking 10. 4 Utilities Disposition 10. 5 Work Control During Excavations 10. 6 The Excavation Process 10. 7 As-Built Drawings

Chapter 11 - Enclosed Electrical/Electronic Equipment 11. 1 Grounding and Bonding 11. 2 Rack Power Distribution 11. 3 Chassis Power Distribution 11. 4 Protective Devices for Enclosed Elect. Equipment 11. 5 Disconnecting Means 11. 6 Marking and Labeling Requirements 11. 7 Working Clearances 11. 8 Cable/Utility Management System 11. 9 Electrical Safety Requirements for Tester Facilities 11. 10 Enclosed Power Electronics 11. 11 Non-ionizing Radiation 11. 12 Ampacity Information for Wire Sizing

Chapter 12 – Approval of Unlisted Electrical Equipment This Chapter, created by our EFCOG group was pushed to an Appendix

Chapter 13 Research and Development 13. 1 Operation and Maintenance 13. 2 Employee Qualifications 13. 3 Generic R&D Equipment 13. 4 Methods 13. 5 Requirements for Specific R&D Equipment

Chapter 14 References ANSI ASME ASTM Crane DOE CFR IEEE ISA NEMA NFPA UL Other

Ideas for New Material • • • Lithium Ion batteries Solar Power systems Emergency Response for electrical systems LOTO Lessons Learned Mixed hazard PPE Risk Assessment Tools, mobile app, etc. . Superconducting magnets Best practices (subsurface detection, LOTO) Lightning protection EFCOG working group products

Ideas for User tools • Flow chart linked to sections • Mobile App for hazard classification and controls • Mobile App for DOE handbook

Options for DOE Electrical Safety Handbook • Updates to existing handbook, DOE • Updates and add new material, DOE • Completely restructure handbook, DOE – Eliminate redundant code info, reorder • Break into two handbooks – Existing application of codes to labs, DOE – Research laboratories, Science and NNSA, EFCOG • Pull handbook out of DOE, make it EFCOG handbook

DOE Electrical Safety Handbook proposed 1) Introduction 2) General Requirements 3) Hazard Analysis 4) Risk Assessment 5) Electrical Preventive Maintenance 6) Grounding 7) Special Occupancies 8) Requirements for Specific Equipment code 9) Work in Excess of 600 V 10) Temporary Wiring 11) Electrical Safety During Excavation 12) Enclosed Electrical/Electronic Equipment 13) Unlisted Electrical Equipment Approval 14) Research and Development 15) Electrical Severity Measurement Tool A – DOE Model Electrical Safety Program B – Acronyms and Definitions C – Unlisted Electrical Equipment - EFCO D – Hazard Analysis - EFCOG E – Referenced Citations F – Severity Tool general R&D, both code, explosives code R&D R&D code EFCOG

DOE Electrical Safety Handbook – 2 Handbooks 1) Introduction 2) General Requirements 3) Electrical Preventive Maintenance 4) Grounding 5) Special Occupancies 6) Requirements for Specific Equipment 7) Work in Excess of 600 V 8) Temporary Wiring 9) Electrical Safety During Excavation A – DOE Model Electrical Safety Program B – Acronyms and Definitions E – Referenced Citations general code, explosives code 1) Introduction 2) General Requirements 3) Hazard Analysis 4) Risk Assessment 5) Enclosed Electrical/Electronic Equipment 6) Unlisted Electrical Equipment Approval 7) Research and Development 8) Electrical Severity Measurement Tool A – Acronyms and Definitions general R&D, both R&D R&D code

EFCOG Electrical Safety Handbook 1) Introduction 2) General Requirements 3) Hazard Analysis 4) Risk Assessment 5) Enclosed Electrical/Electronic Equipment 6) Unlisted Electrical Equipment Approval 7) Research and Development 8) Electrical Severity Measurement Tool A – Acronyms and Definitions