Document for Technical and Sales Training KXNS 1000

Document for Technical and Sales Training KX-NS 1000 Basic Specification January 14, 2016 Panasonic System Networks PBX SE team This document explains basic specification of KX-NS 1000 version 4. 3. It is recommended to know basic specification of KX-NS small PBX (KXNS 300 -500 -700) before reading this document. Specifications are subject to change without notice.

1. Introduction KX-NS 1000 is bigger capacity model of KX-NS PBX series. KX-NS 1000 supports 1, 000 extensions. 1, 000 IP phone or 1, 000 Digital PT or 1, 000 SLT or 1, 000 mixture KX-NS 1000 supports lots of built-in solution. Voice Mail, Unified Message, Recording, Call center, Unified Communication, Mobility, Conference, One-look networking and so on KX-NS 1000 KX-NS 8188 E 1 adapter KX-NS 8290 PRI adapter Built-in Solution KX-NS 1000 Slave Master KX-NS 0130 IP Network KX-TDE 620 etc 1, 000 Extension KX-DT w/ DSS Console SLT KX-NT KX-HDV Other SIP KX-DT SIP Phone Softphone Max. 16 KX-NS 1000 KX-T 7 xxx SLT 100 % Feature transparency like TDE 600 and TDE 620 2

2. Feature Difference KX-NS small PBX and KX-NS 1000 have same feature basically like KXNCP and KX-TDE. Feature difference is as follows. Feature KX-NS small PBX KX-NS 1000 Yes (as slave) Yes KX-NS 300/500 : Yes / KX-NS 700 : No Yes No but SMDR through LAN Yes LAN port 10/100 Base TX 10/1000 WAN port No Yes MNT port No but USB port with adapter Yes Fax to e-mail No Yes Sensor to e-mail Yes (Version 4. 1) Built in VM (UM) 24 -ch 30 -ch (Version 4. 1) Simple VM Yes (*) No Modem : KX-TDA 0196 Yes (*) No PT Program Yes (*) No 40, 000 calls SMDR by SD Yes (*) No One-look network Trunk Adapter : KX-NS 8188/8290 RS 232 port (*) These features are not available when KX-NS small PBX is connected with KX-NS 1000 by one-look network. 3

3. Table of Contents Chapter Contents 1 Basic configuration 2 Stacking card / One-look networking 3 Trunk adapter (E 1/PRI) 4 WAN (Built-in Router) 5 Activation key 6 Capacity (Review & Conditions) 4

Chapter 1 Basic Configuration 5

11. Capacity is as follows. Line NS 1000 x 1 NS 1000 x 2 NS 1000 x 3 to 16 256 x 2 600 Legacy 256 x 2 600 IP incl E 1/PRI adapter 256 SIP incl PRI Public mode 256 H. 323 incl PRI QSIG mode 48 96 640 1000 480 SLT (*1) 512 DPT (*2) 1000 640 1000 Trunk Extension Digital PT / Analog PT / SLT IP 600 Trunk + 1000 Extension is available. Trunk + Extension total capacity of KX-TDE 600 was limited because total 43 free slot by KX-TDE 600 + 3 x KX-TDE 620. But KX-NS 1000 can support lots of KX-TDE 620. (*1) 24 SLT x 10 by TDE 620 x 2 for example (*2) 256 DPT including DXDP by TDE 620 x 2 for example TDE 600 + TDE 620 x 3 100 % Feature Transparency like TDE 600 to TDE 620 NS 1000 x 4 + TDE 620 x 8 for example 1000 Digital PT is available using Digital XDP because one DLC 16 occupies 32 -ch. 6

12. Capacity with QSIG H. 323 QSIG connection provides Max. 256 x <1, 000 extensions by “NS 1000 master with NS 1000 slave and KX-TDE 620 etc”>. - Network DSS key can be used in 8 PBXs. - KX-TDE/NCP also can be connected using H. 323 QSIG. - It is very unusual that more than 96 users in 1, 000 extensions have to talk with extensions in other IP Network PBX at the same time. (VPN) 96 -ch is enough. 96 ch H. 323 96 ch KX-DT SLT KX-NT KX-HDV 1000 Ext NS 1000 x 2 NS 1000 1000 Ext x 2 96 ch 1000 Ext 96 ch 32 ch KX-DT SLT 100 % Feature Transparency like TDE 600 and TDE 620 KX-DT SLT KX-NT KX-HDV 1000 Ext KX-DT SLT 100 % Feature Transparency like TDE 600 and TDE 620 512 x <640 extensions by one KX-NS 1000> is also available with 48 ch H. 323. 7

13. KX-NS 1000 Main Unit Front View A D C B G H E J I Back View N M O P Q F R A 3 Indicator for (1) System (2) Battery (3) Master / Slave B Default Switch C USB Port D LAN port for maintenance PC (*) E LAN Port for customer network F WAN Port M Power Switch N Earth Terminal O AC Inlet P Clip Hole for AC cable Q MPR ID R RS-232 C Port G MOH Port H Pager Port I Doorphone Slot J Free Slot (*) D is independent from E. D is useful when PC for maintenance is not allowed to connect to customer’s network. D and E for TDE/NCP were for same network. 8

14. Optional Cards on Mother Board Two DSP can be installed. Hot swap is not available. 9

15. Optional Cards on Front 2 analogue trunk ports with Caller ID (FSK/FSK with Call Waiting Caller ID /DTMF). One port is a power failure transfer (PFT) port. 2 extension ports with Caller ID (FSK) for SLTs. Hot swap is not available. 10

Chapter 2 Stacking Card One-look Network 11

21. Stacking Card When customer needs lots of analog SLT, digital PT, analog CO, PRI and so on, KX-NS 1000 with stacking card KX-NS 0130 is useful. - KX-TDA 100 -200 -620, KX-TDE or KX-NCP works as slave unit. - 2 slave units are supported with one KX-NS 1000 by one KX-NS 0130. - KX-NS 0131/0132 is installed to slave unit instead of MPR or BUS card. - KX-TDA(E)620 cannot be connected with KX-TDA(E)600 by BUS card. KX-NS 1000 Built-in Solution KX-NS 0130 DSP KX-DT w/ DSS Console Stacking card for NS 1000 KX-NS 0131 Stacking card for NCP KX-NS 0132 Stacking card for TDA/TDE IP Network KX-TDE 620 etc 640 Extension KX-NS 0130 SLT KX-NT KX-HDV Other SIP Phone Softphone 100 % Feature transparency like TDE 600 and TDE 620 12

22. One-look Networking A maximum of 12 KX-TDA/TDE/NCP and 16 KX-NS 1000 can be connected for the entire One-look Network for 1, 000 extensions. One-look networking is similar to TDE 600 -TDE 620 connection. KX-NS 1000 master works like KX-TDE 600. Other units work like KX-TDE 620. All programming is available through KX-NS 1000 master like KX-TDE 600. Activation key : KX-NSN 001 is required for each KX-NS PBX. Max. 16 Built-in KX-NS 1000 Solution KX-NS 1000 Slave Master KX-NS 0130 DSP KX-DT w/ DSS Console KX-NS 0130 IP Network KX-TDE 620 etc Max. 12 KX-TDA/TDE/NCP 1, 000 Extension DSP SLT KX-NT KX-UDV Other SIP KX-DT SIP Phone Softphone KX-T 7 xxx SLT 100 % Feature transparency like TDE 600 and TDE 620 Maximum of KX-TDA/TDE/NCP was 8 for KX-NS 1000 version 4. 0 or before. 13

23. One-look Networking with KX-NS small PBX A maximum of 15 KX-NS small PBX also can be connected for the entire One-look Network as slave PBX. Master PBX should be KX-NS 1000. Activation key : KX-NSN 001 is required for each PBX. Hardware : DSP such as KX-NS 5110 is required because Vo. IP is used for connection. (A) Max. 12 KX-TDA/TDE/NCP (B) Max. 24 KX-NS 320 KX-NS 520 KX-NS 720 KX-NS 1000 DSP KX-NS 0130 KX-NS small PBX DSP IP Network (C) KX-NS 1000 master + 15 KX-NS 1000 or KX-NS small PBX Max. 1, 000 Extension (A)+(B) Total DSP TDA/TDE/NCP 0 1 2 3 4 5 6 7 8 9 10 11 12 NSx 20 24 22 20 18 16 14 12 10 8 6 4 2 0 KX-NS 300 : SD card such as KX-NS 3134 is also required. (KX-NSF 990 AK is required when KX-NS 300 needs IP trunk, IP extension or UM. ) KX-NS small PBX cannot be master (including back-up master) because not enough CPU. 14

24. Upgrade from QSIG When customer is using KX-TDA/TDE/NCP with Q-SIG, KX-NS 1000 with one-look networking is useful for more features such as paging. IP Network KX-TDE 620 Stacking KX-TDE 600 KX-NCP IP Network KX-TDE 600 Stacking KX-TDE 620 Stacking KX-NCP Stacking Max. 12 PBXs QSIG KX-DT KX-DT Paging 100 % Feature transparency 15

25. Stacking Card – Conditions (1) - Different PBX category cannot be mixed to one KX-NS 1000. Category 1 : KX-NCP 500 -1000 IP Network Category 2 : KX-TDE(A)100 -200 Stacking Category 3 : KX-TDE(A)600 -620 KX-TDE 600 KX-TDE 620 KX-NCP Stacking Category 4 : KX-TDA 100 D Stacking NCP 500+TDE 200 : N/A TDE 100+TDA 200 : OK TDE 600+TDE 620 : OK TDE 620+TDE 620 : OK KX-DT - Card configuration for optional cards in KX-TDA/TDE/NCP with stacking card does not change from KX-TDA/TDE/NCP with MPR. For example, Max. 4 PRI cards can be installed to KX-TDE 200. KX-TDA 1178 cannot be installed to KX-TDA 600. Max. 5 KX-TDA 1178 can be installed to KX-TDE 200. (MEC is not required for KX-TDA 1176/1178 in KX-TDE 100 -200 with stacking card. ) - KX-TDA 100 -200 -620 with stacking card is treated as KX-TDE 100 -200 - 600 -620 for above condition. 16

26. Stacking Card – Conditions (2) - Cards in right table are not supported. Reason is as follows. - MPR is removed. - IP feature is supported by KX-NS 1000. - DISA feature is supported by KX-NS 1000 using Vo. IP DSP card. - IP phones should be registered to KX-NS 1000 does NOT support KX-NT 136, KX-NT 400, KX-HGT 100 and so on. - IP capacity AK is not required for trunk and extension in existing PBXs because these are not IP. - Other AK such as CA is required in KX-NS 1000 for extension in existing PBX. Not Supported Symbol Model RMT TDA 0196 MEC TDA 0105/ TDE 0105 DSP 4 NCP 1104 DSP 16 TDE 0110 DSP 64 TDE 0111 CTI-LINK TDA 0410 IP-EXT 16 TDA 0470 IP-GW 4 E TDA 0484 IP-GW 16 TDA 0490 IP GW 4 TDA 0480 MSG 4 TDA 0191 ESVM 2 TDA 0192 ESVM 4 TDA 0194 - In case of TDA 100/200 and TDE 100/200, OPB 3 card with ECHO 16 must be installed to Slot 1. *) Other cards except OPB 3 or OPB 3 card with other daughter board except ECHO 16 can be installed to any slot. 17

Chapter 3 Trunk Adapter (E 1/PRI) 18

31. E 1 / PRI Adapter When customer needs IP-Phone mainly for extension and uses E 1 or more than 2 PRI as trunk, KX-NS 1000 with trunk adapter is useful. Trunk adapter is connected using SIP trunk. Activation key for IP trunk is not required to connect E 1 / PRI adapter. Trunk adapter cannot be connected with other PBX using SIP. Panasonic KX-NS 8290 PRI 30 Trunk Adaptor Model Specifications KX-NS 8188 X E 1 adapter on SIP trunk KX-NS 8290 CE PRI 30 adapter on SIP trunk KX-NS 8290 X PRI 23 adapter on SIP trunk SIP Extension SIP Trunk (30 -ch) IP Trunk AK PRI 30 KX-NS 1000 PRI Card KX-NCS 0290 IP Network 215 mm (W) 44 mm (H) 200 mm (D) 500 g KX-NT KX-HDV Other SIP Phone SIP Softphone 19

32. PRI Adapter - Fractional service is also available. <Stand alone> 20 ch E 1/PRI Trunk Adaptor KX-NS 1000 20 ch <One-look network> 20 ch E 1/PRI Trunk Adaptor 60 ch E 1/PRI Trunk Adaptor 10 ch E 1/PRI Trunk Adaptor Total 256 ch 20 ch 1 st KX-NS 1000 in Fukuoka 30 ch 2 nd KX-NS 1000 in Tokyo 30 ch 16 th KX-NS 1000 in Niseko 20

33. PRI Adapter - QSIG PRI adapter supports ISDN QSIG also to connect with other PBX. Trunk adapter is connected using H. 323 trunk. Activation key for IP trunk is not required for PRI adapter. Trunk adapter cannot be connected with other PBX using H. 323. 192. 168. 0. 101 192. 168. 0. 151 P Ext 2 xx IP Trunk AK H. 323 Trunk Adaptor R I ISDN QSIG Ext 1 xx KX-TDA/TDE/NCP or 192. 168. 30. 101 PBX by other maker IP Network (VPN) Ext 3 xx KX-NS 1000 DN 2 IP table (Dial to IP) -----------------Dial 2 xx to 192. 168. 0. 151 Dial 3 xx to 192. 168. 30. 101 Dial 4 xx to 192. 168. 40. 101 Ext 4 xx 21

Chapter 4 WAN (Built-in Router) 22

41. WAN (Built-in Router) is supported from KX-NS 1000 version 3. Hardware for WAN is available since version 1 mass production. Activation key : KX-NSN 101 is required. One internet line can be used for both PC and Vo. IP. LAN IP Network WAN Router Port Fwd LAN for Maintenance LAN (Customer’s network) 223. 0. 0. 1 (Default) 192. 168. 0. 101 (Default) When customer wants to add one more internet for Vo. IP (Extension or Trunk), Add one more router. IP Network Or use built-in router. Port Fwd is not required. WAN Router Fwd Router LAN IP Network WAN 23

42. Built-in VPN WAN / Built-in Router can support VPN (IP-SEC) feature also. VPN is required if one-kook network is configured using built-in router. Activation key : KX-NSN 216 is required. (KX-NSN 101 is also required. ) One KX-NSN 216 supports 16 VPN connection. Max. two AKs can be supported for 32 VPN connection. IP phone also can be connected using VPN for secured communication instead of MRG feature. Easy Installation even for VPN by Panasonic technology “VPSS”. IP Network VPN Router External VPN Router 24

Chapter 5 Activation Key 25

51. Activation key only for KX-NS 1000 Following activation key is only for KX-NS 1000. 26

52. Activation Key for Expansion Following activation key was added from KX-NS 1000 version 3. These AK are required for each master and slave PBX. Model Name Feature Maximum KX-NSX 910 Expansion AK from NSM 005 1 AK IP phone Capacity is increased to 100 ports KX-NSX 930 Expansion AK from NSM 010 1 AK IP phone Capacity is increased to 300 ports KX-NSX 999 Expansion AK from NSM 030 1 AK IP phone Capacity is increased to 640 ports 30 50 Description 100 300 640 IP phone Pre-installed NSX 930 NSX 910 NSM 005 NSX 930 NSM 010 NSM 030 NSM 099 NSX 999 60 days free trial is NOT available. 27

53. Pre-installed Activation Key Following features are available without buying activation key and without expiration. IP Extension for KX-NT/UT/HDV/NTV hardware phone : 8 ch - Not for KX-NT 700 and KX-NT based software phone - Not for 3 rd party SIP phone => Easy to sell Panasonic KX-NT/UT/HDV/NTV UM (Built-in KX-TVM) : 2 ch CA Basic (Built-in server / External server) : All users 28

Chapter 6 Capacity (Review and Conditions) 29

61. Capacity - Summary Capacity is as follows. Line NS 1000 x 1 NS 1000 x 2 NS 1000 x 3 to 16 256 x 2 600 Legacy 256 x 2 600 IP incl E 1/PRI adapter 256 SIP incl PRI Public mode 256 H. 323 incl PRI QSIG mode 48 96 640 1000 480 SLT (*1) 512 DPT (*2) 1000 640 1000 Trunk Extension Digital PT / Analog PT / SLT IP (*3) (*1) 24 SLT x 10 by TDE 620 x 2 for example (*2) 256 DPT including DXDP by TDE 620 x 2 for example (*3) For example, KX-NS 1000 x 1 as master + KX-NS small PBX x 2 also can support 1, 000 extensions. Capacity is occupied when hardware card and virtual IP card are installed, even if phone is not connected actually. For example, one DLC 16 in KX-NS 1000 or KX-NS small PBX connected by one-look network occupies 32 -ch including Digital XDP. 30

62. Capacity - KX-NT capacity for one unit of KX-NS 1000 can be increased. Type 1 or Type 2 can be selected after default clear. Type 1 (Default) Stand Alone One-look 640 1000 IP-PT (KX-NT series) 256 1000 SIP incl KX-UT/HDV/NTV 640 1000 Stand Alone One-look 640 1000 IP-PT (KX-NT series) 640 1000 SIP incl KX-UT/HDV/NTV 256 1000 IP 　 Type 2 IP 　 Type 3 is also available to increase H. 323 ch. : 128 ch for NS 1000 2 or more unit But capacity of IP extension reduces. See Installation manual for details. 31

63. Capacity - Conditions One VM channel reduces 10 -port extension capacity of master PBX because CPU of master PBX needs more power for VM. - Default 2 -ch does not reduce this. - Extension capacity of slave PBX does not reduce, even if slave PBX has VM because CPU of slave PBX is not so busy. Total 1000 extensions Master PBX VM (ch) VM Extension Slave PBX VM (ch) VM Extension Default 2 640 2+2 620 2+2 640 2+4 600 2+4 640 : : 2 + 22 420 2 + 22 640 This condition is applied to KX-NS 1000 only. (Not to KX-NS small PBX) 32

64. Capacity - Configuration Tool Required hardware and activation key can be advised using tool by MS Excel. Web edition is also available for more features. 33

Thank you ! 34

Revision Date No. Aug 22, 2014 All First release Nov 5, 2014 2 KX-NS 1000 version 4. 1 supports 30 -ch Built-in VM (UM). April 2, 2015 11 (Page 6) 24 (Page 15) Version 4. 1 supports 12 KX-TDA(E) and NCP. 23 (Page 14) NSF 991 is not required for one-look network of KXNS 700. 53 (Page 28) Version 4. 2 supports KX-HDV IP phone using KXNSM 5 xx AK. (Same AK for KX-NT/UT) Dec 14, 2015 23 (Page 14) KX-NS 300 : (KX-NSF 990 AK is required when KX-NS 300 needs IP trunk, IP extension or UM. ) Jan 14, 2016 53 (Page 28) Version 4. 3 supports KX-NTV using KX-NSM 5 xx AK. (Same AK for KX-NT/UT) All 66 to 68 Change KX-HDV is used as example instead of KX-UT. Picture of KX-NT 300 is revised to KX-NT 500. Information for DSP was moved to “DSP Guide”. 35