Chapter 10 Design of Experiments and Analysis of
- Slides: 27
Chapter 10 Design of Experiments and Analysis of Variance
Elements of a Designed Experiment • Response variable Also called the dependent variable • Factors (quantitative and qualitative) Also called the independent variables • Factor Levels • Treatments • Experimental Unit 2
Elements of a Designed Experiment Designed vs. Observational Experiment • In a Designed Experiment, the analyst determines the treatments, methods of assigning units to treatments. • In an Observational Experiment, the analyst observes treatments and responses, but does not determine treatments • Many experiments are a mix of designed and observational 3
Elements of a Designed Experiment Single-Factor Experiment Population of Interest Sample Independent Variable Dependent Variable 4
Elements of a Designed Experiment Two-factor Experiment 5
The Completely Randomized Design Achieved when the samples of experimental units for each treatment are random and independent of each other Design is used to compare the treatment means: 6
The Completely Randomized Design • • The hypotheses are tested by comparing the differences between the treatment means to the amount of sampling variability present Test statistic is calculated using measures of variability within treatment groups and measures of variability between treatment groups 7
The Completely Randomized Design Sum of Squares for Treatments (SST) Measure of the total variation between treatment means, with k treatments Calculated by Where 8
The Completely Randomized Design Sum of Squares for Error (SSE) Measure of the variability around treatment means attributable to sampling error Calculated by After substitution, SSE can be rewritten as 9
The Completely Randomized Design Mean Square for Treatments (MST) Measure of the variability among treatment means Mean Square for Error (MSE) Measure of sampling variability within treatments 10
The Completely Randomized Design F-Statistic Ratio of MST to MSE Values of F close to 1 suggest that population means do not differ Values further away from 1 suggest variation among means exceeds that within means, supports Ha 11
The Completely Randomized Design Conditions Required for a Valid ANOVA FTest: Completely Randomized Design 1. Independent, randomly selected samples. 2. All sampled populations have distributions that approximate normal distribution 3. The k population variances are equal 12
The Completely Randomized Design A Format for an ANOVA summary table 13
The Completely Randomized Design ANOVA summary table: an example from Minitab 14
The Completely Randomized Design Conducting an ANOVA for a Completely Randomized Design 1. 2. 3. 4. 5. Assure randomness of design, and independence, randomness of samples Check normality, equal variance assumptions Create ANOVA summary table Conduct multiple comparisons for pairs of means as necessary/desired If H 0 not rejected, consider possible explanations, keeping in mind the possibility of a Type II error 15
Multiple Comparisons of Means • A significant F-test in an ANOVA tells you that the treatment means as a group are statistically different. • Does not tell you which pairs of means differ statistically from each other • With k treatment means, there are c different pairs of means that can be compared, with c calculated as 16
Multiple Comparisons of Means • Three widely used techniques for making multiple comparisons of a set of treatment means • In each technique, confidence intervals are constructed around differences between means to facilitate comparison of pairs of means • Selection of technique is based on experimental design and comparisons of interest • Most statistical analysis packages provide the analyst with a choice of the procedures used by the three techniques for calculating confidence intervals for differences between treatment means 17
Multiple Comparisons of Means 18
The Randomized Block Design Two-step procedure for the Randomized Block Design: 1. Form b blocks (matched sets of experimental units) of k units, where k is the number of treatments. 2. Randomly assign one unit from each block to each treatment. (Total responses, n=bk) 19
The Randomized Block Design Partitioning Sum of Squares 20
The Randomized Block Design Calculating Mean Squares Setting Hypotheses Hypothesis Testing Rejection region: F > F , F based on (k-1), (n-b-k+1) degrees of freedom 21
The Randomized Block Design Conditions Required for a Valid ANOVA FTest: Randomized Block Design 1. The b blocks are randomly selected, all k treatments are randomly applied to each block 2. Distributions of all bk combinations are approximately normal 3. The bk distributions have equal variances 22
The Randomized Block Design Conducting an ANOVA for a Randomized Block Design 1. 2. 3. 4. 5. 6. Ensure design consists of blocks, random assignment of treatments to units in block Check normality, equal variance assumptions Create ANOVA summary table Conduct multiple comparisons for pairs of means as necessary/desired If H 0 not rejected, consider possible explanations, keeping in mind the possibility of a Type II error If desired, conduct test of H 0 that block means are equal 23
Factorial Experiments Complete Factorial Experiment • Every factor-level combination is utilized 24
Factorial Experiments Partitioning Total Sum of Squares • Usually done with statistical package 25
Factorial Experiments Conducting an ANOVA for a Factorial Design 1. 2. 3. 4. 5. 6. Partition Total Sum of Squares into Treatment and Error components Test H 0 that treatment means are equal. If H 0 is rejected proceed to step 3 Partition Treatment Sum of Squares into Main Effect and Interaction Sum of Squares Test H 0 that factors A and B do not interact. If H 0 is rejected, go to step 6. If H 0 is not rejected, go to step 5. Test for main effects of Factor A and Factor B Compare the treatment means 26
Factorial Experiments SPSS ANOVA Output for a factorial experiment 27
- Design and analysis of ecological experiments "torrent"
- Chapter 13 experiments and observational studies
- Design of experiments doe
- Jmp doe analysis
- Design of experiments six sigma
- Design of experiments pmp example
- Design of experiments presentation
- Worked out
- Design of experiments pmp
- Design of experiments
- Six sigma betekenis
- Design of experiments
- Chapter 2 american experiments summary
- System and form design example
- Observational survey examples
- What are surveys experiments or observation
- 2k factorial experiments and fractions
- Miller and urey's experiments attempted to demonstrate
- Counting rule for multiple-step experiment
- Pro cons animal testing
- User interface design in system analysis and design
- Dialogue design in system analysis and design
- Disadvantages of structured analysis
- Fact-finding techniques in system analysis and design
- Operational feasibility
- [http://earthobservatory.nasa.gov/experiments/biome/]
- Test your hypothesis
- Piaget 1896