CAFS Compressed Air Foam System Class Objectives Understand

CAFS Compressed Air Foam System

Class Objectives - Understand the uses for Compressed Air Foam - Understand the basics of the foam concentrate used by the GFD - Understand basic components of the CAFS - Understand the basic operation of the CAFS - Understand the daily and monthly maintenance

Uses For Compressed Air Foam Advantages of Compressed Air Foam Based on studies starting back in the 1970’s through the 2000’s by numerous agencies which included: - Texas Department of Forestry - Boston Fire Department - Los Angeles City Fire Department - Los Angeles County Fire Department

Uses For Compressed Air Foam Advantages of Compressed Air Foam - Uses less water - extinguishment of given test fire (Boston Fire) 69 gallons = Water 30 gallons = CAF - extinguishment of given test fire (Boston Fire) 100 gallons = Water 36 gallons = CAF - extinguishment of given test fire (LAFD) 75 gallons = Water 16 gallons = CAF - Less accumulated weight (reduced chance of structural collapse)

Uses For Compressed Air Foam Advantages of Compressed Air Foam - Absorbs heat more rapidly due to greater surface area of a given volume of water - cool a test fire from 1000 degrees F to 212 degrees F (NIFC) 222. 9 seconds = Water 38. 5 seconds = CAF - cool a room from 600 degrees F to 200 degrees F (LAFD) 363 seconds = Water 88 seconds = CAF

Uses For Compressed Air Foam Advantages of Compressed Air Foam - Reduces the weight of hose lines - Reduces water and smoke damage - Reduces property damage - Deceases rekindle - Clings to surfaces for exposure protection - Forms a vapor barrier and excludes oxygen

Uses For Compressed Air Foam Disadvantages of Compressed Air Foam - Adds expense to apparatus - Hose reaction can be erratic if air ratio is off - Accentuates reaction of hose is it ruptures - Is under utilized do to lack of training

Uses For Compressed Air Foam CAF can be mixed either wet or dry - Wet CAF - Fire Attack - Mansards - Attic Fires - Basement Fires - Overhaul - Dry CAF - Pre-treating - Overhaul

Foam Concentrate Phos-Chek WD-881

Foam Concentrate Phos-Chek WD-881 - Manufactured by ICL ( was acquired from Monsanto) - Class A - Can be used at 0. 1 – 1. 0% ( recommended 0. 2 -0. 5% for CAFS) - 85% reverts to carbon dioxide within 28 days of exposure to ambient conditions in the environment - Can be used on Class B but will breakdown and must be reapplied (consider accumulation of water due to repeated applications)

Foam Concentrate Phos-Chek WD-881 - Health effects and Toxicological Information: Ingestion: “practically nontoxic” Skin Contact: “no more than slightly toxic” and moderately irritating Eye Contact: severely irritating Inhalation: may cause nose and upper respiratory irritation - These are greatly reduced when mixed at foam solution concentrations

Basic System Components 3 Subsystems Of The Hercules CAFS - Water Pump - Foam Proportioning System - either Husky 10 or 12 depending on year - Air Compressor System

Basic System Components Air Compressor System (basic components)

Basic System Components Control Panel - Turning the compressor on/off - Setting foam or tool mode - Displaying the air flow - capable of at least 140 SCFM at 150 psi - Oil Temperature - 165 to 210 degrees F normal range - High oil temperature warning - Activates at 250 degrees F

Basic System Components Pressure Control Valve - Operates compressor through a range of 60 to 150 psi - Matches air pressure to water pressure (+ or - 5%) Check Valves - Keeps water from flowing into the air circuit - Keeps air from pressurizing back into the pump

Basic System Components Air Compressor - Rotary screw type - Hydraulically driven off transmission PTO - Oil cooled with thermostat and oil/water heat exchanger that uses discharged pump water to control its temperature

Basic System Operation 4 Steps to producing Compressed Air Foam - Flow Water - Add Foam - Add Compressed Air - Adjust product to desired consistency

Basic System Operation Flow Water - Check compressor oil (sight gauge) and foam tank levels: part of pre-check - Engage pump and establish water supply (tank or hydrant) Intake gated down to 50 psi Note: Manual states 70 psi - Cannot flow additional lines when using CAF

Basic System Operation Add Foam - Turn on Husky Foam System - Adjust percentage to. 2 to. 5% (default is. 5%) - Confirm foam solution is flowing

Basic System Operation Add Compressed Air - Turn on Hercules System (must be under 1000 RPM and less than 30 psi air in system) - Set to “Foam” (“Auto” on some engines) - Confirm air pressure is building on gauge - Open CAFS air to Discharge

Basic System Operation Adjusting product to desired consistency (Dry) - Initial pump discharge at 100 psi - Gate discharge down to produce dryer foam - Adjust foam percentage (0. 2 – 0. 5%) - Good dry foam can be made as low as. 2% - There tends to be a fine line between good

Basic System Operation Adjusting product to desired consistency (Dry) - Use a nozzle ball valve without the nozzle or a smooth bore tip (1 3/8”) - Fog nozzles will strip the air - Lob foam from a distance or bank off an object if trying not to disrupt the foam blanket

Basic System Inspection/Maintenance Check compressor oil - Daily and after every use - oil should be between ½ and ¾ on sight gauge - wait 10 minutes is it was just used Check hydraulic fluid reservoir - Daily and after every use - Visually inspect hoses, filter, compressor for leaks Operate Husky 10 / 12 monthly - Prevents foam concentrate from congealing in

Basic System Inspection/Maintenance Operate compressor monthly - Uncap CAFS Discharge - Put in pump gear - Open the discharge air supply valve - Turn on the compressor - Bring pump pressure up to 125 psi while recirculating of flowing water - Run for 10 to 20 minutes - Monitor pump and compressor temperatures

Final Points To Remember It’s not on the F-295, but exercise the system monthly - The more it is used, the better it works - It keeps components and valving moving freely There is no perfect setting for dry foam - Each rig is slightly different - Will require manipulation to dial the system in for good quality foam - May require periodic adjustment while in use

Questions ?